Abstract:At the cartilage-to-bone interface, the residing cells are different with respects to metabolic requirements. Fabrication of a scaffold affording different metabolic needs of these cells can be taken account of a promoting step for regeneration of cartilage- to-bone interface. In the present study, a scaffold with a depth-dependent gradient of oxygen releasing microparticles was developed. To this end, oxygen releasing microparticles were fabricated from polylactic acid (PLA) and calcium peroxide and then dispersed in hydrogel precursor of functionalized pectin and fibroin. The microparticles were loaded in a hydrogel precursor solution in a gradient manner using a gradient mixing chamber. The mixing chamber was composed of two compartments filled with hydrogel precursors with different microparticle contents (10 and 30% w/w) and an interfacial mixing port. The velocity of microparticle loaded solution inside the gradient chamber was modeled using momentum balance Navier-Stokes equations. Moreover, spatial and temporal variations of microparticle concentration in the gradient chamber were modeled using mass transfer Navier-Stokes equations. Chemical, morphological and structural variations across the composite thickness were evaluated using microscopy and spectroscopy analyses. The model proposed by Navier-Stokes equation corroborated that the flow velocity was different in various domains of the mixing chamber and in the vicinity of the mixing port the velocity was substantially higher than the bulk flow. Moreover, the velocity profile showed gradual velocity changes from bulk to the mixing port. The model represented for microparticle concentration proved that microparticle content of precursor solution varied both spatially and temporally. As time goes by, the microparticle concentration gradually increased from about 10% w/w and approached to about 30% w/w at the end of the process. SEM micrographs from the cross-section of composite corroborated that microparticle density gradually increased from the lower to the upper surface. Spectroscopy confirmed that the oxygen releasing component, i.e. calcium peroxide, increased across the said direction. Oxygen measurement from successive sections of composite revealed that the amount of produced oxygen increased from the lowermost to the uppermost section. In conclusion, the hydrogel/particle composite with a gradient in oxygen releasing component can be a promising scaffold to satisfy the different metabolic needs of cells at the cartilage- to-bone interface. STATEMENT OF SIGNIFICANCE: Numerous tissue engineering scaffolds have been so far fabricated to recapitulate the gradient nature of cartilage- to-bone interface. Chemical, mechanical, structural and even electrical gradients of cartilage- to-bone interface have been tried to imitate by those scaffolds. However, scaffold with a gradient in metabolic features has not been developed yet. At the cartilage-to-bone interface, the residing cells are different with respects to metabolic requirements. Therefore, fabrication of a scaffold affording different metabolic needs of these cells can be taken account of a promoting step for regeneration of cartilage- to-bone interface. In the present study, a scaffold with a depth-dependent gradient of oxygen releasing microparticles was developed using a gradient making chamber. In addition to mathematical modeling of flow velocity and microparticle concentration in gradient making device, the depth-dependent changes in morphology, chemistry and structure of hydrogel/particle composite were experimentally evaluated.

Cylindrical polyester/calcium peroxide oxygen-releasing microparticles: molecular dynamics simulation and experimental analyses

Tuning Microparticle Porosity During Single Needle Electrospraying Synthesis Via A Non-Solvent-Based Physicochemical Approach

Nanostructured Poly(l-Lactic Acid)-Poly(ethylene Glycol)-Poly(l-lactic Acid) Triblock Copolymers and Their CO2/O-2 Permselectivity

Preparation, characterization and biocompatibility of calcium peroxide-loaded polycaprolactone microparticles

Effect of Oxygen on Surface Properties and Drug Release Behavior of Plasma Polymer of N-Butyl Methacrylate

Preparation And Properties Of Polylactide/Poly(Ethylene-Co-Octene)/Nano-Sio2 Ternary Composites

Fabrication and Characterization of Oxygen-Generating Polylactic Acid/Calcium Peroxide Composite Filaments for Bone Scaffolds

Bulk Erosion Degradation Mechanism for Poly(1,8-octanediol- co-citrate) Elastomer: An In Vivo and In Vitro Investigation

Poly(lactic acid)/poly(butylene adipate-co-terephthalate) films reinforced with polyhedral oligomeric silsesquioxane nanoparticles: a morphological, mechanical, and thermal study

Mechanical, permeability, and degradation properties of 3D designed poly(1,8 octanediol-co-citrate) scaffolds for soft tissue engineering.

Poly(glycerol Sebacate)-Modified Polylactic Acid Scaffolds with Improved Hydrophilicity, Mechanical Strength and Bioactivity for Bone Tissue Regeneration

Modeling Strategies for the Degradation Behavior of Porous Polyester Materials Based on Their Key Structural Features

Raspberry-like PLA/PGS biodegradable microparticles with urethane linkages: Unlocking tailored release of magnesium ions and oxygen for bone tissue engineering

Effect of Poly(Ethylene Glycol) on the Properties and Foaming Behavior of Macroporous Poly(Lactic Acid)/Sodium Chloride Scaffold

Controlled Release of Oxygen from Calcium Peroxide in a Weak Acidic Condition by Stabilized Amorphous Calcium Carbonate Nanocoating for Biomedical Applications

Improving Phase Compatibility of PLA-PCL Matrix-Droplet Blend Using CNC/PCL-PEG-PCL Triblock Copolymer to Prepare Porous 3D Osteoinductive Scaffolds

A hydrogel/particle composite with gradient in oxygen releasing microparticle for oxygenation of the cartilage-to-bone interface: Modeling and experimental viewpoints

Surface modification of POSS-nanocomposite biomaterials using reactive oxygen plasma treatment for cardiovascular surgical implant applications

Porous polymeric structures for tissue engineering prepared by a coagulation, compression moulding and salt leaching technique

Mild Fabrication of Polymeric Porous/Nonporous Micro‐Composite Structures via Enhancing the Photothermal Conversion of Ultrafast Laser

Effect of water content on microstructures and oxygen permeation in PSiMA–IPN–PMPC hydrogel: a molecular simulation study