Abstract:The MAX phase has attracted much attention due to its unique properties combined with the merits of both metal and ceramic, including the low density, high electrical conductivity and good oxidation resistance, which makes it significant for possible applications in various high temperature or other environments. There is a lot of research work on Ti2AlX (X=C, N). However little research about thermodynamic properties at high pressure is carried out. So we study the structural, mechanical and thermodynamic properties of Ti2AlC and Ti2AlN at various pressures and temperatures. The first-principles calculations based on electronic density-functional theory framework are used to investigate the properties at various pressures. The cut-off energy is 350 eV. Converged results are achieved with 10102 special K-point meshes. The self-consistent convergence of total energy is set to be 5.010-6 eV/atom. According to the calculated structural parameters at various pressures, we can find that the ratios V/V0 (V0 denotes the system volume at 0 GPa) of Ti2AlX are reduced by 20.59% and 18.93%, respectively, so the compressibility of the system is strong. As the internal pressure increases, the curves of V/V0 become gentle. Then we calculate elastic constants at pressures ranging from 0 to 50 GPa in steps of 10 GPa. It is obvious that the Ti2AlX is mechanically stable because all of the elastic constants satisfy the Born stability criteria. The bulk modulus, shear modulus and Young's modulus linearly increase with internal pressure increasing, implying that the pressure can improve the resistance to volume deformation. The ductility and brittleness can be judged according to Pugh's criterion (ratio of bulk modulus to shear modulus B/G), and the brittle nature turns into ductile nature in a pressure range of 40-50 GPa for the Ti2AlX since the value of B/G exceeds 1.75. Finally, we study the thermodynamic properties at various pressures and temperatures based on the quasi-harmonic Debye approximation theory, including the bulk modulus, heat capacity and thermal expansion coefficient. The bulk modulus decreases with temperature increasing but increases with pressure increasing. The heat capacity at constant volume Cv and the heat capacity at constant pressure Cp have the same variation tendency, while Cv obeys the Dulong-Petit limit. It is easy to see that temperature and pressure have opposite influences on heat capacity and the effect of temperature is more significant than that of pressure. The effects of temperature and pressure on linear expansion coefficient mainly occur at low temperature and the effect of pressure is not so considerable when the pressure exceeds 30 GPa. Above all, the effects of temperature and pressure on thermodynamic properties are inverse.

Temperature-dependent structural, mechanical, and thermodynamic properties of B2-phase Ti2AlNb for aerospace applications

Investigation on the Microstructure and Mechanical Behaviors of a Laser Formed Nb-Ti-Al Alloy

Theoretical Investigation of the High Pressure Structure, Lattice Dynamics, Phase Transition, and Thermal Equation of State of Titanium Metal

Microstructure Evolution and Mechanical Properties of High Nb-TiAl Intermetallic Compounds during Heat Treatment

Study of the Mechanical and Thermodynamic Properties on NiAl and Ni3Al

Mechanical Properties and Oxidation Characteristics of TiNiAl(Nb) Intermetallics

Structural, Mechanical, and Thermodynamic Properties of Ti2AlX (X = C, N) at High Pressure

Effect of Trace Boron Addition on the Microstructural Evolution and Mechanical Properties in Ti45al8nb2cr-B Alloys

Thermal Expansion of a Multiphase Intermetallic Ti-Al-Nb-Mo Alloy Studied by High-Energy X-ray Diffraction

Mechanical Properties of Ti2AlNb and Ti2AlZr Intermetallics: A First Principles Study

Phase equilibria, thermodynamic assessment, and the mechanical property of B2 phase of the Al-Ga-Ni ternary system

Structural, elastic, electronic, bonding, thermo-mechanical and optical properties of predicted NbAlB MAB phase in comparison to MoAlB: DFT based ab-initio insights

First-Principles Investigations of the Structural, Anisotropic Mechanical, Thermodynamic and Electronic Properties of the AlNi2Ti Compound

First-principles thermodynamic investigation on the α phases in TiO and TiNb binary system

Microstructure, Phase Stability and Mechanical Properties of Nb–Ni–Ti–Co–Zr and Nb–Ni–Ti–Co–Zr–Hf High Entropy Alloys

Microstructure, Mechanical, and Tribological Properties of Nb-Doped TiAl Alloys Fabricated via Laser Metal Deposition

Electronic Structure Of Ti2alnb (O Phase)

Investigation of the ordering and atomic site occupancies of Nb-doped TiAl/Ti3Al intermetallics

The Effect of Nb Doping on the Properties of Ti-Al Intermetallic Compounds Using First-Principles Calculations

Crystallographic orientation relationships and interfacial structures between reinforcement and matrix phases in an in situ (Ti, Nb)B/Ti2AlNb composite

First-principles calculation on the structural, elastic and thermodynamic properties of Ti-Al intermetallics