Abstract:In the production process, people usually pay more attention to the parts' technical performance and production cost while ignoring the influence of the production process on workers' health and the environment. Therefore, in this paper, the multi-objective optimization for grinding process with AISI 1045 steel was conducted to obtain the optimal scheme of the workpiece feed velocities, the depths of cutting and cooling/lubrication conditions. The residual stress, surface roughness, production cost, production rate, operator health and CO2 emission were evaluated as optimization objectives. A series of models were proposed and revised to apply to the flood and small quantity cooling/lubrication grinding conditions. Grinding is a high specific energy processing method, and the grinding surface of the metal workpiece usually generates large tensile residual stress due to excessive grinding heat, which does harm to the surface quality and fatigue life of products. Therefore the residual stress and surface roughness were evaluated as the technical benefit by experiments. The production rate and production cost as the economic benefit, the harm of grinding fluid to machine tools operators as the healthy benefit, and the CO2 emission as the environmental benefit were considered based on models. An orthogonal experiment was designed by Taguchi method. The contribution rates of each objective and their corresponding sub-objectives were calculated by grey relational analysis to avoid the correlation effects among different objectives. Finally, the grinding schemes were optimized by the range analysis and validated by experiments and calculations. The results show that the combined technical, economic, healthy and environmental benefits were improved significantly with the optimal scheme of workpiece feed velocity 2.4 <math>mmin−1</math>, depth of cut 0.03 <math>mm</math>, and small quantity cooling/lubrication. It has an important reference value for green manufacturing. Besides, the feasibility of small quantity cooling/lubrication with water for the grinding process was proved.

Multi-objective optimization of grinding and vibration parameters of ultrasonic-assisted grinding with ultrasonically atomized novel green cutting fluid of Nimonic 80A

Effect of Ultrasonic Vibration Assisted Grinding Process on Surface Topography and Properties of C/SiC Composite

An Experimental Investigation on Ultrasonic Vibration-Assisted Grinding of SiO2f/SiO2Composites

MOPSO Process Parameter Optimization in Ultrasonic Vibration-Assisted Grinding of Hardened Steel

Grindability Evaluation of Ultrasonic Assisted Grinding of Silicon Nitride Ceramic Using Minimum Quantity Lubrication Based SiO2 Nanofluid

Numerical modeling of heat flux in ultrasonic-assisted grinding of difficult-to-cut materials with a pressurized lubrication system

Multi-response optimization in face milling of EN-31 steel using analytical hierarchy process-based GRA

Development and performance of a novel ultrasonic vibration plate sonotrode for grinding

Assessment and optimization of grinding process on AISI 1045 steel in terms of green manufacturing using orthogonal experimental design and grey relational analysis

Experimental Study on Ultrasonic Vibration Assisted Grinding of GCr15SiMn Bearing Steel

Research on the effect of grinding force on the axial ultrasonic vibration-assisted grinding of Ti-6Al-4V with multi-grain conical grinding head

Multiple Performance Characteristics in the Application of Taguchi Fuzzy Method in Nanofluid/Ultrasonic Atomization Minimum Quantity Lubrication for Grinding Inconel 718 Alloys

Optimal Design of Parameters for the Nanofluid/Ultrasonic Atomization Minimal Quantity Lubrication in a Micromilling Process

Optimization of Machining Parameters for Ultrasonic Assisted Vibration-Grinding (UAVG) of Ultra-Low Expansion (ULE) Optical Glass Using Taguchi Method

Sustainability assessment associated with surface roughness and power consumption characteristics in nanofluid MQL-assisted turning of AISI 1045 steel

Multi-Constraint Optimization for Grinding Nickel-Based Alloys

New knowledge about grinding using MQL simultaneous to cooled air and MQL combined to wheel cleaning jet technique

Molecular dynamics simulations of ultrasonic vibration-assisted grinding of polycrystalline iron: Nanoscale plastic deformation mechanism and microstructural evolution

Multi-objective parametric optimization for high surface quality and process efficiency in micro-grinding

Mechanism and Experimental Evaluation on Surface Morphology of GCr15SiMn with Ultrasonic Vibration Grinding

An intelligent multi-objective optimization method for transverse profile grinding processes of large shafts