Abstract:Abstract Metal-composite laminates and joints are applied in aircraft manufacturing and maintenance (repairing) using aluminum alloys (AA) and glass fiber-reinforced polymer (GFRP). In these applications, drilling has a prominent place due to its vast application in aeronautical structures’ mechanical joints. Thus, this study presents the influence of uncoated carbide drills (85C, 86C, H10N), cutting speeds ( v c = 20, 40, and 60 m min −1 ), and feed rates ( f = 0.05, 0.15, and 0.25 mm rev −1 ) on delamination factor, thrust force ( F t {F}_{\text{t}} ), and burr formation in dry drilling metal-composite laminates and joints (AA2024/GFRP/AA2024). Experiments were performed, analyzed, and optimized using the Box–Behnken statistical design. Microscopic digital images for delamination evaluation, piezoelectric dynamometer for thrust force acquisition, and burr analysis were considered. The major finding was that the thrust force during drilling depends significantly on the feed rate. Another significant factor was the influence of the drill type (combined or not with feed rate). In fact, it was verified that the feed rate and the drill type were the most significant parameters on the delamination factor, while the feed rate was the most relevant on thrust force. The cutting speed did not affect significantly thrust force and delamination factor at exit ( F da S ) \hspace{.25em}({F}_{{\text{da}}_{\text{S}}}) . However, the combination f × v c was significant in delamination factor at entrance ( F da E ) \text{ }({F}_{{\text{da}}_{\text{E}}}) . Based on the optimized input parameters, they presented lower values for delamination factors ( F da E = 1.18 {F}_{{\text{da}}_{\text{E}}}=1.18 and F da S = 1.33 {F}_{{\text{da}}_{\text{S}}}=\hspace{.25em}1.33 ) and thrust force ( F t = 67.3 N {F}_{\text{t}}=67.3\hspace{.5em}\text{N} ). These values were obtained by drilling the metal-composite laminates with 85C-tool, 0.05 mm rev −1 feed rate, and 20 m min −1 cutting speed. However, the burrs at the hole output of AA2024 were considered unsatisfactory for this specific condition, which implies additional investigation.

Optimization and alternative image processing approach for the comprehensive assessment of delamination and uncut fiber in drilling fiber metal laminate

Cutting parameters optimization of hybrid fiber composite during drilling

Optimization of Drilling Parameters on Delamination and Burr Formation in Drilling of Neat CFRP and Hybrid CFRP Nano-Composites

Optimization of drilling parameters to minimize delamination in (PEKK/CFRP) thermoplastic polymer matrix composites for aerospace applications

Experimental Investigation of drill tool types on delamination error in drilling of CFRP

Prediction of Delamination Defects in Drilling of Carbon Fiber Reinforced Polymers Using a Regression-Based Approach

Delamination assessment and prediction in ultrasonic-assisted drilling of laminated hybrid composites

Optimizing Process Parameters in Drilling of CFRP Laminates: A Combined MOORA–TOPSIS–VIKOR Approach

Machinability Of Drilling T700/Lt-03a Carbon Fiber Reinforced Plastic (Cfrp) Composite Laminates Using Candle Stick Drill And Multi-Facet Drill

Influence of Drilling Parameters on the Delamination and Surface Roughness of Insulative-Coated Glass/Carbon-Hybrid Composite

Effects of drilling parameters on delamination of kenaf-glass fibre reinforced unsaturated polyester composites

Experimental Analysis and Application of a Multivariable Regression Technique to Define the Optimal Drilling Conditions for Carbon Fiber Reinforced Polymer (CFRP) Composites

Thermo-Mechanical and Delamination Properties in Drilling GFRP Composites by Various Drill Angles

Optimization for drilling process of metal-composite aeronautical structures

Effect of Drilling Parameters and Tool Geometry on the Thrust Force and Surface Roughness of Aerospace Grade Laminate Composites

Image Analysis Techniques Applied in the Drilling of a Carbon Fibre Reinforced Polymer and Aluminium Multi-Material to Assess the Delamination Damage

Investigation of the effect of AWJ drilling parameters for delamination factor and surface roughness on GFRP composite material

Effect of drilling parameters on hole quality in drilling of pultruded GFRP composite material: Surface roughness, thrust force and delamination factor

Defects Study on Drilling of Carbon Fiber Reinforced Polymer (CFRP) Laminates

Effects of Specialized Drill Bits on Hoe Defects of CFRP Laminates

Investigation of delamination and surface quality of machined holes in drilling of multiwalled carbon nanotube doped epoxy/carbon fiber reinforced polymer nanocomposite