Abstract:Journal of Reinforced Plastics and Composites, Ahead of Print. Polymer-based composites (GFRP) are increasingly used in the mechanical industry due to their cost-profitability, durability, and good mechanical properties. In the present study, a metal carbide tool was employed to manufacture polyamide (PA66-GF30%) specimen in a dry environment. The impact of variations in cutting process parameters on the responses studied is investigated using two experimental techniques. The first is the OFAT approach. For the second technique (multifactorial), the effects of input parameters on technological parameters (Ra, Fz, MRR, and Pc) are quantified aided by the ANOVA method using an experimental design based on Taguchi's L9 (3 × 3) orthogonal matrix. Based on the RSM methodology, the results were processed statistically to propose prediction models for the different outputs. In addition, a single-objective optimization study of Taguchi's and a multi-objective optimization of the operating conditions using the classification method based on CoCoSo as well as the DF Approach according to two desired objectives were carried out. The first objective of this study concerns the minimization of (Ra, Fz, and Pc), and the second one considers the minimization of (Ra, Fz, and Pc) at the same time as maximizing (MRR). Finally, the surface roughness criteria (Ra and Sa) of PA66-GF30% were evaluated to study the effect of the feed (f) on the machined surface topography. The findings are of capital importance in that they provide the required and correct information about the working conditions of composite polymers. According to "OFAT" results, feed (f) is the predominant factor influencing roughness (Ra). Temperature in the cutting zone rises with increasing cutting conditions (Vc, f and ap). Variations in cutting conditions affect the morphology of the chip produced. The roughness criteria (Ra and Sa) results clearly show that the topography of the PA66-GF30% surface changes as (f) changes. Also, optimization of all performance parameters simultaneously indicates that the DFA offers the best combination of parameters: Vc = 187.50 m × min−1, f = 0.096 mm × rev−1, and ap = 0.866 mm, leading to the minimization of (Ra) and maximization of (MRR), with respective values of 1.24 μm and 15.614 cm3 × min−1. Furthermore, the CoCoSo method favors the minimization of (Fz and Pc) with values of 20.18 N and 69.285 W, respectively.

Investigation of the effect of AWJ drilling parameters for delamination factor and surface roughness on GFRP composite material

Optimization of machining parameters for kerf angle and roundness error in abrasive water jet drilling of CFRP composites with different fiber orientation angles

Optimization of AWJ parameters for improved material removal and hole geometry in drilling of Glass Fiber/Aluminum mesh epoxy hybrid composites

Effect of drilling parameters on hole quality in drilling of pultruded GFRP composite material: Surface roughness, thrust force and delamination factor

Simultaneous optimization of process parameters during abrasive water jet machining on glass fibre reinforced polymer

Abrasive water jet machining of glass fibre reinforced polymer composite: experimental investigation, modelling and optimization

An experimental and empirical assessment of machining damage of hybrid glass-carbon FRP composite during abrasive water jet machining

Evaluating the optimum abrasive water jet machinability for CARALL composites with various fiber orientations

Bearing strength performance: A study on the influence of AWJ drilling and delamination of GF/Al‐mesh reinforced polymer composites

Influence of Drilling Parameters on the Delamination and Surface Roughness of Insulative-Coated Glass/Carbon-Hybrid Composite

Optimization of Drilling Parameters on Delamination and Burr Formation in Drilling of Neat CFRP and Hybrid CFRP Nano-Composites

Secondary Processing of Aramid with AWJ and Optimization with NSGA-III

Effect of Abrasive Water Jet Parameters on the Drilling of Aluminum Foam Sandwiched with Glass Fiber Polymer Composites

Optimization of drilling parameters to minimize delamination in (PEKK/CFRP) thermoplastic polymer matrix composites for aerospace applications

Understanding the Effect of Drilling Parameters on Hole Quality of Fiber-Reinforced Polymer Structures

Effect of Drilling Parameters and Tool Geometry on the Thrust Force and Surface Roughness of Aerospace Grade Laminate Composites

Advanced Material Processing: Optimization of Abrasive Water Jet Parameters for Metal-Stacked Hybrid Fiber Laminate

Cutting parameters optimization of hybrid fiber composite during drilling

Study on Machining Quality in Abrasive Water Jet Machining of Jute-Polymer Composite and Optimization of Process Parameters through Grey Relational Analysis

Effects of drilling parameters on delamination of kenaf-glass fibre reinforced unsaturated polyester composites

Investigation on machining of GFRP through ANOVA, DFA, and CoCoSo method combined with Taguchi approach