Abstract:One completely new geometry and two modified chip breaker geometries were designed to increase the stability and reliability of the stainless steel dry drilling process. Experiments were performed and the results of individual tools were compared with a conventional solid carbide twist drill Gühring Ratio with a diameter of 5 mm. A matrix of three feed rates (0,03–0,07 mm/rev) and three cutting speeds (20–30 m/min) was designed for the cutting conditions. Precipitation-hardenable stainless steel 17-4 PH was chosen as a workpiece. During the experiment, the values of thrust force, spindle torque, temperature of the tool, surface roughness, chips morphology and chips division were recorded and compared with the reference tool. The results showed that compared to the reference tool A, the tool C - a multipoint drill with grooves through the cutting edge achieve approximately 4 % lower values of thrust force and 10–15 % lower values of spindle torque. Tool D with a step drill geometry achieve approximately 17 % lower values of thrust force and 10–15 % lower values of spindle torque and there is no chip clogging in the flute with C and D geometries. This effect is confirmed by the fact the spindle torque basically does not increase with the increasing depth of drilling. Tool B – new designed geometry achieve approximately 15 % lower values of thrust force and similar spindle torque values as the reference drill A. Tool temperature is a very important factor when dry drilling. Compared to the reference drill A, it was possible to achieve the tool temperature reduction of 20 % with the new geometry B, as well as with the multipoint drill C reduction by 26 % and with the step drill D reduction approximately by 30 %. All the modified drills also achieved a reduction in the surface roughness of the drilled holes. By 17 %, 35 % and 48 % lower surface roughness Ra was achieved with drills B, C and D. Chip morphology was significantly different for the tested drills. Conventional twist drills A and B generated helical short chips. While C and D twist drills with divided cutting edges generated ribbon snarled chips. Thanks to the reduction of cutting forces and temperature, it is possible to stably operate the drilling process with a higher cutting speed and feed rate, which leads to an increase in the efficiency and reliability of the machining process.

Enhancement of Deep Drilling for Stainless Steels by Nano-Lubricant through Twist Drill Bits

A Multiscale Evaluation of the Surface Integrity in Boring Trepanning Association Deep Hole Drilling

Ultrasonic assisted nano-fluid MQL in deep drilling of hard-to-cut materials

Assessing the lubrication performance of various vegetable oil-based nano-cutting fluids via eco-friendly MQL technique in drilling of AISI 321 stainless steel

Enhanced Performance of Micro Deep Drawing through the Application of TiO2 Nanolubricant and Graphene Lubricants on SUS 301 Stainless Steel Foil

Novel drill geometries for dry drilling of stainless steel

Investigation of Surface Integrity of 304 Stainless Steel in Turning Process with Nanofluid Minimum-Quantity Lubrication Using h-BN Nanoparticles

Improved Rheological Properties and Lubricity of Drilling Fluids at Extreme Temperatures and Pressures Using Graphene Oxide and Flowzan

A novel graphene/triolein complex-based lubricant for improving high temperature water-based drilling fluid

A study on the lubrication effects of nano‐TiO2 additive water‐based lubricants during rolling of ferritic stainless steel strips

Experimental investigations on surface integrity and chip morphology in hard tuning of AISI D3 steel under sustainable nanofluid-based minimum quantity lubrication

Influence of MoS2-Based Nanofluid Minimum Quantity Lubrication on Machining Performance of AISI 316L Stainless Steel

Drilling performance analysis on super duplex stainless steel (AISI 2507) using scalable pulse power plasma TiSiN- and AlTiN-coated tools and optimizing machining parameters through Taguchi–Fuzzy approach

Organic-Sulfonate Functionalized Graphene as a High Temperature Lubricant for Efficient Antifriction and Antiwear in Water Based Drilling Fluid

Lubricity and Rheological Properties of Highly Dispersed Graphite in Clay-Water-Based Drilling Fluids

Research on Wear Mechanism of Coated HSS Drills during Machining Stainless Steel

Machinability study of stainless steel AISI 304 under the influence of copper oxide nanoparticles dispersed emulsifier cutting fluidUntersuchung der Zerspanbarkeit von rostfreiem Stahl X5CrNi18 10 unter dem Einfluss von mit Kupferoxid‐Nanopartikeln dispergiertem Emulgator‐Kühlschmierstoff

Synergistic Tribological Behaviors of Graphene Oxide and Nanodiamond As Lubricating Additives in Water

Analysis of TiO2 Nanolubricant Influence in Micro Deep Drawing of Stainless Steel SUS301

Using Nano-Fluids Minimum Quantity Lubrication (NF-MQL) to Improve Tool Wear Characteristics for Efficient Machining of CFRP/Ti6Al4V Aeronautical Structural Composite

Evaluation of MQL performances using various nanofluids in turning of AISI 304 stainless steel