Abstract:Introduction The Biggest challenges coal-fired power plants are facing are improving their energy efficiencies and reducing their environmental impact due to CO2 and NOX emissions, can be attained by maximizing the steam pressure and temperature. However, the operating temperatures and pressures in boiler materials were restricted due to limited weldability of essential dissimilar joints between Austenitic Stainless Steel (ASS) and Creep-Enhanced Ferritic Steel (CEFS) due to carbon migration and sensitization. Present research work provides enhanced metallurgical and mechanical properties of weldment by optimizing the welding process and welding parameters. Aim The aim of the manuscript is to explores the welding compatibility of TP347H (stabilized ASS) with solution annealed T91 (CEFS), by Auto TIG welding technique, such that carbon migration at the fusion line of SA213 T91 and sensitization in the heat affected zone of TP347H can be minimized. Methods Influence of Auto TIG welding parameters on the mechanical, microstructure, and corrosion properties are studied and discussed. Carbon migration, mechanical and corrosion properties for lower (0.792 KJ/mm) and higher (1.124 KJ/mm) heat inputs weldments were compared. Investigation on mechanical properties test such as tensile, hardness, and root bend performed as per American Society of Mechanical Engineers (ASME) Section IX. Optical microscopy and Analytical Scanning Electron Microscope (SEM) coupled with Energy Dispersive Spectroscopy (EDS) have been performed to investigate carbon migration and sensitization behaviour. Sensitization susceptibility further validated by American Society for Testing and Materials (ASTM) A 262 Practice E. Results Investigation on tensile, hardness, and root bend tests revealed that mechanical properties for lower heat input weldment were superior. Restricted carbon migration due to optimized heat input improves mechanical properties and this was evidenced by satisfactory results of the bend test which showed no opening at the fusion line. A noticeable improvement in Ultimate Tensile Strength (UTS) 666 and 680N/mm2 (compared to 578 and 561N/mm2 for 1.124 KJ/mm heat input) and an acceptable hardness of 307 HV (compared to 399 HV for 1.124 KJ/mm heat input) were observed at T91 and weld metal interface. No fissures on bend surface and no Cr23C6 precipitation at grain boundary after performing ASTM A 262 Practice E and SEM-EDS respectively on heat affected zone (TP347H) of lower heat input weldment which shows higher resistance to intergranular corrosion (Sensitization). Conclusion Optimizing the welding parameters and decreasing the heat input mitigate the carbon migration at T91 fusion zone and, meeting the requirements for satisfactory mechanical properties in materials used for power generation applications. Further optimized welding heat input have lesser Cr23C6 precipitation in the heat-affected zone of TP347H, making the heat affected zone less susceptible to sensitization. Heat input must be controlled to (1) avoid intergranular corrosion failure or sensitization and (2) improve the mechanical properties of the weldment where requirement of post weld heat treatment is mandatory in the application (as recommended in the ASME Section 1, PW 39.1).

Mechanical Properties and Corrosion Resistance of Cold Metal Transfer Small-Bore Thin-Walled Tube Butt Welded Joints of UNS S32205 Duplex Stainless Steel

DSI-based Studies of the Effects of High-temperature Aging on Local Mechanical Properties of HR3C/T92 Dissimilar Steel Welded Joint

Study on Microstructure and Properties of Cold Metal Transfer and Pulse Hybrid Welded Super Duplex Stainless Steel

Microstructural characteristics of different heat-affected zones in welded joints of UNS S32304 duplex stainless steel using the GMAW process: analysis of the pitting corrosion resistance

A comparison of microstructure and mechanical characteristics correlation of the joint specimens for duplex stainless steel UNS S32304 and super-duplex stainless steel UNS S32750: The role of post-weld heat treatment

Investigation on microstructure evolution, mechanical properties and corrosion resistance of dual phase stainless steel joints welded by GTAW and SAW methods

The Microstructure and Pitting Corrosion Behavior of K-TIG Welded Joints of the UNS S32101 Duplex Stainless Steel

Corrosion Properties and Impact Toughness of 2205 Duplex Stainless Steel after TIG Welding*

Effect of Post-Weld Heat Treatment on Microstructure Evolution and Pitting Corrosion Behavior of UNS S31803 Duplex Stainless Steel Welds

Cold Metal Transfer Welding of Ferritic and Austenitic Stainless Steel: Microstructural, Mechanical, and Electrochemical Studies

Effect Of Solubilization Heat Treatment On Microstructure And Corrosion Resistance Of Joints Welded With The Autogenous Tig Process Duplex Stainless Steel

Metallurgical and Corrosion Characterization of Austenitic Stainless Steel Welds during Post Weld Heat Treatment

Mechanical Properties Of A Thermally-Aged Cast Duplex Stainless Steel By In Situ Tensile Test At The Service Temperature

Experimental Investigation On The Microstructure And Mechanical Properties Of Dss2205 And Ss304L Dissimilar Weldments

Effect of Thermal Cycles on the Corrosion and Mechanical Properties of UNS S31803 Duplex Stainless Steel

Mechanical properties and corrosion resistance study of dissimilar metal thin sheet friction stir welded joints

Microstructure and Mechanical Properties of Friction Stir Welded 2205 Duplex Stainless Steel Butt Joints

Crucial Microstructural Features to Determine the Mechanical Properties of Welded Joints in a Cu-Containing Low-Carbon Low-Alloy Steel After Postweld Heat Treatment

Dissimilar joining of duplex AISI 2304 stainless steel/austenitic AISI 321 stainless steel using resistance spot welding technique: Microstructural evolutions, tensile-shear properties, and fracture analysis

Determination and Characterization of Heat Input, Microstructure and Performance in Cold Metal Transfer Weld-Brazing of Dissimilar AA6061-T6 to SS304 Sheets

Mechanical and intergranular corrosion properties of auto TIG welded TP347H-T91 dissimilar weldments