Abstract:Previous studies have yet to show a consistent effect of severe plastic deformation (SPD) processing on the wear behavior of different metals and alloys. To fill this scientific gap, this study investigated the effect of the cyclic extrusion compression (CEC) process, as one of the prominent SPD techniques, on the wear behavior of AA5052. In addition, the microstructure evolution and mechanical properties of the sample before and after the process were experimentally examined and studied. It was found that the yield and ultimate tensile strength of the AA5052 improved significantly after the first pass, while the elongation-to-failure decreased considerably. Further, the subsequent passes mildly changed the trend of increasing strength and reducing elongation-to-failure. SEM morphology indicated that the ductile mode of the initial annealed alloy changed to a combination of ductile and brittle failure modes, in which the level of the brittle failure mode increased with the addition of passes. TEM observations showed that the grain refinement during the CEC process included the formation of dislocation cell structures, subgrain boundaries, and low-angle grain boundaries, with the subgrain boundaries initially evolving into low-angle grain boundaries and, eventually, due to the imposition of additional plastic strain, into high-angle grain boundaries. Furthermore, the CEC process and its increased number of passes led to a significant improvement in wear resistance due to the enhanced tensile strength achieved through grain refinement. In this regard, the wear mechanism of the initial alloy was a combination of adhesion and delamination, with the plastic deformation bands changing to plowing bands with decreased adhesive wear during the process. Eventually, oxidization was found to be a mechanism contributing to wear under all conditions.

Effect of Hard Cyclic Viscoplastic Deformation on the Microstructure, Mechanical Properties, and Electrical Conductivity of Cu-Cr Alloy

Effect of cryogenic impact deformation and subsequent annealing on microstructure and microhardness of pure copper

Effect of ECAP by Route BC and Aging Heat Treatment on the Structure and Properties of Cu0.4Cr0.3Zr Alloy

Effect of ECAP Processing on Hardness, Electrical Conductivity, and Precipitation Kinetics of the Cu-0.81Cr-0.07Zr Alloy

Experimental Study on Pure Copper Subjected to Different Severe Plastic Deformation Modes

Micro/nanostructure high strength and high conductivity CuCrZr alloy prepared through equal channel angular pressing and aging treatment

Strain effects on the wear rate of severely deformed copper

Characterization of microstructural evolution and mechanical properties of Cu-Ni-Cr alloys deformed by ECAP

Relief of Strain Hardening in Deformed Inconel 718 by High-Density Pulsed Electric Current

Ultrahigh Deformability of Ti-6Al-4V Assisted by High-Density Pulsed Electric Current Treatment

Effect of High-Density Pulsed Electric Current on the Formability of Aluminum Alloy

Unveiling Thermal and Athermal Effects in Strain Hardening Removal of A6061 Aluminum Alloy

Deformation Microstructure and Property Control of CuCrZr Alloy Directionally Solidified at Room Temperature C-ECAP

Effect of Aging Treatment on Microhardness and Electrical Conductivity of Extruded CuCr25 Alloy

Cyclic Extrusion Compression Process for Achieving Ultrafine-Grained 5052 Aluminum Alloy with Eminent Strength and Wear Resistance

Experimental and Numerical Investigation of the ECAP Processed Copper: Microstructural Evolution, Crystallographic Texture and Hardness Homogeneity

Effect of grain refinement on mechanical and electrochemical properties of severely deformed pure copper through equal channel angular pressing

Hardness and Texture of Electrolytic Copper Processed by ECAP at Ambient and Warm Temperature

Effects of Deformation on Microstructures and Properties of Submicron Crystalline Cu-5%Cr Alloy

Effect of heat treatments on microstructure, mechanical and electrical properties of Cu–Cr–Zr alloy manufactured by laser powder bed fusion

Effect of whisker alignment on microstructure, mechanical and thermal properties of Mg-SiC w /Cu composite fabricated by a combination of casting and severe plastic deformation (SPD)