Abstract:<p>High borated steel sheets containing 0.25 wt% to 4.0 wt% boron including hypoeutectic (0.28 wt% B and 2.11 wt% B), eutectic (2.43 wt% B) and hypereutectic (4.01 wt% B) compositions were tried to be fabricated by a novel strip casting technology, and the effects of boron content on sub-rapid solidification behavior and subsequent microstructural evolution together with mechanical properties was studied. It was found that the morphology of borides depended greatly on the boron content. When increasing boron, the morphological change of borides was network-like → grainy → cluster-like → plate-like. Various orientation relationships between different morphological borides and γ-Fe in as-cast steels were also identified. After subsequent hot-rolling and solution-treating, ultra-fine (<10 μm) borides were obtained in hypoeutectic and eutectic steels. Benefiting from that, excellent mechanical properties was achieved, which was much better than that of steels prepared by traditional ingot casting. Particularly, when the boron content approached eutectic composition, of which the effect on the microstructure and mechanical properties was more sensitive. The steels containing 2.11 wt% and 2.43 wt% boron exhibited different morphological borides with a total elongation of 14.1% and 8.0%, respectively. Moreover, a thin hypereutectic borated steel sheet was also prepared, but the borides were very large and the total elongation was very low. The correlation between microstructure and strength was clarified based on the Hall-Petch behavior and intermetallic strengthening effect. Smaller γ-grains and higher volume fraction of borides were responsible for higher strength. The plastic behavior of steels was influenced by strain-hardening rate that was determined by the volume fraction of γ-Fe matrix. A better sustainable strain-hardening capability was beneficial to extend the stage of uniform deformation and enhance the ductility. In addition, the mechanical properties of steels were also decided by the fracture mechanism that was dominated by the size of borides.</p>

Stress Development During Cooling of Continuously Cast Boron-Containing Steel Slabs

Simulation Analysis of Thermal Stress During Casting Process of Large-Sized Alloy Steel Ingot

Continuous Casting Mould for Square Steel Billet Optimised by Solidification Shrinkage Simulation

Effect of Grade on Thermal–Mechanical Behavior of Steel During Initial Solidification

DTA study and thermodynamic prediction of the solidification interval of boron 500HB abrasion-resistant steel

Effect of Boron on the Formation of the Naturally Deposited Film and Its Corresponding Interfacial Heat Transfer Behavior in Strip Casting of Boron-Containing Steel

Analysis of heat transfer and thermal stress in continuous casting with mechanical reduction

A 2.5D finite element model for bending and straightening in continuous casting of steel slabs

Prediction and Analysis on Formation of Internal Cracks in Continuously Cast Slabs by Mathematical Models.

Application of Modeling and Simulation of Thermal Stress in Solidification Process of a Heavy Steel Casting

Numerical Simulation and Experiments Research on Secondary Cooling Process of Thick Slab Continuous Casting

The effect of ultra-fast surface hardening and strengthening on microstructure and mechanical properties of cast (9Cr–3Co–3W) heat-resistant steel

Optimization for Secondary Cooling Parameters in Continuous Casting of High Carbon Chromium Bearing Steel

In situ observation and investigation of effect of cooling rate on slab surface microstructure evolution in microalloyed steel

Bending and Straightening of a Medium Carbon Steel Continuous Casting Slab with Low Temperature End Plastic Groove

Simulation Using Realistic Spray Cooling for the Continuous Casting of Multi—component Steel

Analysis and control of surface cracks in a B-bearing continuous casting blooms

Effects of boron content on the microstructure and mechanical properties of twin-roll strip casting borated steel sheets

Differential Microstructure and Properties of Boron Steel Plates Obtained by Water Impinging Jet Quenching Technique

Effect of Boron on Hot Ductility and Room-Temperature Tensile Properties of Microalloyed Steels with Titanium and Niobium

Numerical Simulation of the Thermo-Mechanical Process for Beam Blank Continuous Casting