Abstract:Conventional ultrasound inspection has been a standard non-destructive testing method for providing an in-service evaluation and noninvasive means of probing the interior of a structure. In particular, measurement of the propagation characteristics of Lamb waves allows inspection of plates that are typical components in aerospace industry. A rapid, complete non-contact hybrid approach for excitation and detection of Lamb waves is presented and applied for non-destructive evaluation of composites. An air-coupled transducer (ACT) excites ultrasonic waves on the surface of a composite plate, generating different propagating Lamb wave modes and a laser Doppler vibrometer (LDV) is used to measure the out-of-plane velocity of the plate. This technology, based on direct waveform imaging, focuses on measuring dispersive curves for A0 mode in a composite laminate and its anisotropy. A two-dimensional fast Fourier transform (2D-FFT) is applied to out-of-plane velocity data captured experimentally using LDV to go from the time-spatial domain to frequency-wavenumber domain. The result is a 2D array of amplitudes at discrete frequencies and wavenumbers for A0 mode in a given propagation direction along the composite. The peak values of the curve are then used to construct frequency wavenumber and phase velocity dispersion curves, which are also obtained directly using Snell’s law and the incident angle of the excited ultrasonic waves. A high resolution and strong correlation between numerical and experimental results are observed for dispersive curves with Snell’s law method in comparison to 2D-FFT method. Dispersion curves as well as velocity curves for the composite plate along different directions of wave propagation are measured. The visual read-out of the dispersion curves at different propagation directions as well as the phase velocity curves provide profiling and measurements of the composite anisotropy. The results proved a high sensitivity of the air-coupled and laser ultrasound technique in non-contact characterization of Lamb wave dispersion and material anisotropy of composite plates using simple Snell’s law method.

Features of Laser-Vibrometric Nondestructive Testing of Polymer Composite Materials Using Air-Coupled Ultrasonic Transducers

Features of Laser-Vibrometric Nondestructive Testing of Polymer Composite Materials Using Air-Coupled Ultrasonic Transducers

Specific Features of Nondestructive Testing of Polymer and Composite Materials Using Air-Coupled Ultrasonic Excitation and Laser Vibrometry

Ultrasonic Testing of Carbon Fiber-Reinforced Polymer Composites

Damage Identification in Various Types of Composite Plates Using Guided Waves Excited by a Piezoelectric Transducer and Measured by a Laser Vibrometer

Nondestructive characterization of mechanical properties on metallic and polymer plates using hybrid laser-air coupled ultrasonic techniques

Nondestructive Testing of Thin Composite Structures for Subsurface Defects Detection Using Dynamic Laser Speckles

Diagnosis of early-stage damage to polymer - glass fibre composites using non-contact measurement of vibration signals

Novel NDT Methods for Composite Materials in Aerospace Structures

Features of Thermal Nondestructive Testing of Impact Damage to Products Made of Polymer Composite Materials

Experimental Investigation of Damage Detection in Composite Material Structures Using a Laser Vibrometer and Piezoelectric Actuators

Lamb wave dispersion and anisotropy profiling of composite plates via non-contact air-coupled and laser ultrasound

Nondestructive Evaluation of Debonding in Composites Using Air-Coupled Coda Wave Analysis and Local Defect Resonance Techniques

Feasibility Analysis of Various Sensing Methods for Nondestructive Testing of Composites

Non-contact Defect Imaging of Carbon Fiber Composites Using Laser Excited Acoustic Shearography

ACOUSTIC NON-DESTRUCTIVE TESTING OF MULTILAYERED STRUCTURES FROM PCM DURING THE PRODUCTION AND OPERATION OF AVIATION TECHNIQUE

Application of Laser Ultrasonic Technology for Nondestructive Testing of Aerospace Composites

Development of an Optical Fiber-Guided Robotic Laser Ultrasonic System for Aeronautical Composite Structure Testing

All-optical laser ultrasonic technique for imaging of subsurface defects in carbon fiber reinforced polymer (CFRP) using an optical microphone

Nondestructive Testing of Composite Materials: An In-Depth Study Using Ultrasonic Immersion Inspection

Testing Samples Made of Polymer Composite Materials Using Ultrasonic Antenna Arrays