Abstract:To explore the mechanical properties and fracture modes of basalt fiber-reinforced concrete, single-doped and hybrid-doped basalt fiber-reinforced concrete was prepared, and uniaxial failure tests under different basalt fiber-reinforced concrete contents were carried out. At the same time, the smooth kernel function in the traditional SPH method was improved, and the basalt fiber random generation algorithm was embedded in the SPH program to realize the simulation of the progressive failure of basalt fiber-reinforced concrete. The results show that under the circumstance with no basalt fiber, the specimen final failure mode is damage on the upper and lower surface, as well as the side edge, while the interior of the specimen center is basically intact, indicating that there is an obvious stress concentration phenomenon on the upper and lower surface when the specimen is compressed. Under the circumstance with basalt fiber, longitudinal cracks begin to appear inside the specimen. With the increase in the content, the crack location gradually develops from the edge to the middle, and the crack number gradually increases. This indicates that appropriately increasing the fiber content in concrete may improve the stress state of concrete, change the eccentric compression to axial compression, and indirectly increase the compressive strength of concrete. The numerical simulation results are consistent with the test results, verifying the rationality of the numerical simulation algorithm. For the concrete model without the basalt fiber, shear cracks are generated around the model. For the concrete model with basalt fiber, in addition to shear cracks, the tensile cracks generated at the basalt fiber inside the model eventually lead to the splitting failure of the model. The strength of concrete samples with basalt content of 0.1%, 0.2%, and 0.3% is increased by 1.69%, 5.10%, and 4.31%, respectively, compared to the concrete sample without basalt fiber. It can be seen that with the increase in the content of single-doped basalt fiber, the concrete strength is improved to a certain extent, but the improvement degree is not high; For hybrid-doped basalt fiber-reinforced concrete, the strength of concrete samples with basalt content of 0.1%, 0.2%, and 0.3% is increased by 14.51%, 15.02%, and 30.31%, respectively, compared to the concrete sample without basalt fiber. Therefore, compared with the single-doped basalt fiber process, hybrid doping is easier to improve the strength of concrete.

Numerical simulation of strength of basalt fiber permeable concrete based on CT technology

Three-dimensional Modeling and Simulation of Asphalt Concrete Mixtures Based on X-ray CT Microstructure Images

EXTEND FINITE ELEMENT NUMERICAL SIMULATION FOR CRACK PROPAGATION OF FIBER CONCRETE

Experimental Study on Basic Mechanical Properties of Basalt Fiber Reinforced Concrete

Investigating the Mechanical Characteristics and Fracture Morphologies of Basalt Fiber Concrete: Insights from Uniaxial Compression Tests and Meshless Numerical Simulations

3 D In-situ XCT Image Based Mesoscale Fracture Modelling and Validation of Concrete Using Voxel Hexahedron Meshing and Damage Plasticity Model

Numerical Simulation of Fracture and Damage Behaviour of Concrete at Different Ages

Mechanical Properties and Numerical Analyses of Basalt Fiber Crumb Rubber Mortars in Soft Rock Roadways

3D meso-scale fracture modelling and validation of concrete based on in-situ X-ray Computed Tomography images using damage plasticity model

2D and 3D homogenization and fracture analysis of concrete based on in-situ X-ray Computed Tomography images and Monte Carlo simulations

Numerical Analysis for Basalt Fiber Reinforced High-Viscosity Asphalt Concrete Bridge Deck Pavement

3D Finite Element Simulation of Complex Static and Dynamic Fracture in Quasi-Brittle Materials

Modeling and Simulation of Mechanical Performance in Textile Structural Concrete Composites Reinforced with Basalt Fibers

Measurement of Permeability and the Correlation Between Permeability and Strength of Pervious Concrete

Mechanical Properties under Compression and Microscopy Analysis of Basalt Fiber Reinforced Recycled Aggregate Concrete

Three Dimensional Mesoscopic Simulation of Hydraulic Asphalt Concrete Triaxial Test

Performance Experiments and Finite Element Simulation on Basalt Fiber Reinforced Asphalt Mixture

Numerical Reconstruction Model and Simulation Study of Concrete Based on Damaged Partition Theory and CT Number

Numerical Simulation of Dynamic Mechanical Properties of Concrete under Uniaxial Compression

Study on the tensile properties of basalt fiber reinforced concrete under impact: experimental and theoretical analysis

Experimental study on direct tensile fatigue performance of basalt fiber reinforced concrete