Abstract:The advent of new materials and technologies in building materials has changed the way of building. New lighter materials with easier application methods and improved mechanical behaviors, have become necessary for the market. Moreover, the new environmental policy (2022) aims to transform the waste management into sustainable materials management to ensure the long-term protection and improvement of the environment. For the brick and tile industry, raw materials and the additives that compose the product mixture seem to be a key factor in this direction. Furthermore, every product type (solid or perforated brick) requires different additives to achieve the properties that are postulated by the international standards. For the study, the wide range of additives that were used have been assorted into three (3) categories: the inert materials, the lightweight materials, and the industrial remains. Totally, eight (8) different materials were used as additives into ceramic mass, in different proportions each time. Almost all additives used for this research were pore-forming agents. These burn out almost completely before reaching the full-fire temperature, and do not change the fired body. As a result of additives burnt out, the necessary pore volume is formed in the fired brick body, which, if combined with an appropriate percentage of voids, result in raw density readings. The pore structure is significant as long as the ultimate strength of lightweight bricks is acceptable. In this study, additives between 3 and 25% by weight were added to the clay mixture. The extrusion of specimens in solid form was carried out using the Laboratory’s vacuum press. Firstly, the extrusion of specimens from the original raw material was implemented. Secondly, it was made on the material mixed with the additives mentioned above. A series of experimental activities were followed to determine the variations of the mechanical and physical properties as well as their production procedures (extrusion, drying, and firing). According to five (5) key properties measured in the current study and compared with the mixture without additives, it was found that the variation in thermal conductivity improvement is between -11% and 19%. The bending strength of the fired products showed a decrease from 16% to 55% except for the addition of bauxite residue, which increased the strength by 8%. Bigot drying sensitivity decreased from 11% to 27%. The density in two cases increased from 2% to 7% while in the majority the mixtures with the additives showed a decrease in density from 1% to 14%. Finally, the addition of the necessary water for shaping during extrusion showed a variation from a 10% decreased to a 14% increased water.

Sustainable Reuse of Inorganic Materials in Eco-Friendly Clay Bricks: Special Focus on Mechanical and Durability Assessment

Potential Use of Water Treatment Sludge as Partial Replacement for Clay in Eco-Friendly Fired Clay Bricks

Synergistic effect of rice husk, glass and marble sludges on the engineering characteristics of eco-friendly bricks

Evaluation of physical and mechanical properties of fired-clay bricks incorporating both mineral and organic wastes

Enhancing Mechanical Properties of Clay Brick by Using Stone Powder

Utilization of Plastic Waste Material in Masonry Bricks Production Towards Strength, Durability and Environmental Sustainability

Eco-efficient reuse of alum-based water treatment sludge into structural sintering bricks

Manufacturing of Clay Bricks Using Hybrid Waste Marble Powder and Sugarcane Bagasse Ash: A Sustainable Building Unit

Review of the Use of Sustainable Materials in the Production of Building Units

Mechanical and Durability Properties of Mortars Incorporating Red Mud, Ground Granulated Blast Furnace Slag, and Electric Arc Furnace Dust

Raw Material Design, Sintering Temperature Optimization and Development Mechanism Investigation of Self-Foaming Porous Bricks with High Solid Waste Addition

Innovative Formulations for Building Construction Bricks: Integration of Marble Dust and Lime as Alternatives to Clay for Improved Construction Brick Fabrication

Developing fired clay bricks by incorporating scrap incinerated waste and river dredged sediment

Experimental study on strength and endurance performance of burnt clay bricks incorporating marble waste

Fabrication, Performance And Environmental Safety Of Fired Bricks From Lake Silt And Sewage Sludge Iccs16

Efficient Recovery of Solid Waste Units as Substitutes for Raw Materials in Clay Bricks

An Experimental and Empirical Study on the Use of Waste Marble Powder in Construction Material

Analysing the Effectiveness of Municipal Wastewater Sludge, Bagasse Ash, Rice Husk Ash and Plastic Waste Powder for Manufacturing Bricks

Effect of clay fraction on the mechanical properties and microstructural characteristics of waste rock fine-based brick

Analysis of the Mechanical Properties of Structural Ceramics Made from Aggregate Washing Sludge and Manganese Mining Waste

Recycling of Heavy Metal Contaminated River Sludge into Unfired Green Bricks: Strength, Water Resistance, and Heavy Metals Leaching Behavior – A Laboratory Simulation Study