Abstract:Ti-13 V-3Al (at%) high temperature shape memory alloy was considered attractive material due to its low density. The demand for the better shape memory performance is proposed to widen the scope of application. In the present study, Ti-13 V-3Al is processed by high-pressure torsion and annealing. The microstructure, martensitic transformation and mechanical properties were investigated. The severe plastic deformation introduced high density defects and decreased the stability of the alpha" phase. The phase constitution is the sole beta phase after high-pressure torsion, which was related to the Gibbs-Thomson effect. After the annealing treatment at 700 degrees C, numerous small parallel alpha" martensite variants were observed, which was affected by the residual defects. More nucleation sites were provided, resulting that the reverse martensitic transformation was accomplished in a narrow temperature range. Moreover, the formation of (111) type I twinning become easier due to the assistance of the (111) stacking faults. The alpha" martensite variants became larger and evolved to the V-shaped and the triangular self-accommodated morphologies as the annealing temperature increased to 800 degrees C. The twinning relationship in the different annealing temperature both were the (111) type I twinning. The properties were characterized by the tensile loadingunloading tests and microhardness tests. The shape memory effect was optimized and 4% full recoverable strain was obtained in the alloy annealed at 700 degrees C. The apparent hardness decreased from 323HV and 263HV as the annealing temperature raised from 700 degrees C to 800 degrees C. (C) 2021 Elsevier B.V. All rights reserved.

Influence of the Structure of a VT22I Titanium Alloy on Deformation Mechanisms during the Shape Memory Effect

Influence of structure on mechanisms of VT22I titanium alloy deformation during implementation of shape memory effect

Effect of Structural-Phase State on the Deformation Behavior and Mechanical Properties of Near β Titanium Alloy VT22 in the Temperature Range 293–823 K

Effect of Deformation on the Stress-Induced Martensitic Transformation Behavior of Ti44ni47nb9 Wide Hysteresis Shape Memory Alloy

Deformation Dependence of Transformation Behavior of Ti-Ni-Nb Wide Hysteresis Shape Memory Alloy

Effect of Deformation Temperature on the Microstructure and Texture Evolution of Ti-6Al-4Zr-2Mo-6V Alloy

The Microstructure and Martensitic Transformation of Ti-13V-3Al Light Weight Shape Memory Alloy Deformed by High-Pressure Torsion

The Microstructures and Deformation Mechanism of Hetero-Structured Pure Ti under High Strain Rates

Effect of Strain Rate and Temperature on the Deformation Behavior in a Ti-23.1Nb-2.0Zr-1.0O Titanium Alloy

Effect of mechanical expanding on strain recovery characteristics and microstructures of TiNiNb shape memory alloy

Effect of Microstructure on Strain-hardening Behaviour of a Ti-IF Steel Grade

Effect of Hydrogen on the Development of Deformation and Fracture in Titanium Alloy VT22 in the Temperature Range of 293–823 K

Mechanism of the shape memory effect in martensitic alloys: An assessment

Dynamic Strain-Rate Effect On Uniaxial Tension Deformation Of Ti5al2.5sn Alpha-Titanium Alloy At Various Temperatures

Influence of applied stress on shape memory characteristics of Ni50Ti45Cu5 (at.%) alloy subjected to thermomechanical cycling

Strain rate dependence of deformation-induced transformation and twinning in a metastable titanium alloy

Behavior of Hot Deformation and its Effect Factors for TC4 Titanium Alloy

Deformation Behaviors and Microstructures Evolution of Low Cost Ti-6Al-3V-1Fe-0.25O Alloy

An Experimental Study of Deformation Mechanism and Microstructure Evolution During Hot Deformation of Ti–6Al–2Zr–1Mo–1V Alloy

Formation of the Structure, Phase Composition, and Properties in High-Strength Titanium Alloy upon Isothermal and Thermomechanical Treatment

Effect of Strain on Hot Deformation Behavior and 3-D Processing Maps of a Vanadium and Titanium Microalloyed Steel