Abstract:Superwettability can affect the performance of oil separation from water during the treatment of oily wastewater. Among various types of materials developed for cleaning oil pollution, foam is a popular choice due to its attractive lightweight properties and adjustable porosities. Foams with superwetting surfaces (superhydrophilic/superoleophobic underwater) are ideal for oil/water separations. In this study, lignin-based polyurethane foams (LPUFs) were synthesized first, and then polydopamine particles were deposited on the surface of the foam by in situ polymerization under weak alkaline conditions to increase its surface roughness. Afterwards, phytic acid was used to modify the foam to achieve surface superhydrophilicity and underwater superoleophobicity. Successful loading of polydopamine (PDA) particles and coating of phytic acid (PA) onto the foam was demonstrated by SEM, EDS, FTIR, XPS, and thermogravimetric analysis measurements. It was shown in the cyclic compression tests that LPUFs had good mechanical properties. Under 75 % compression strain, the maximum stress in the first cycle of LPUF/PDA/PA was 105.92 kPa. After 30 cyclic compression tests, the maximum stress of LPUF/PDA/PA under 75 % compression strain was 105.63 kPa, demonstrating a high mechanical stability. The contact angle of the foam modified by PDA and PA was 0° for water, 166.7° for chloroform, and 158.4° for hexane, which also demonstrated excellent underwater anti-oil adhesion performances. Oil-water separation tests by using PDA and PA modified lignin-based foam with mixtures of water and n -hexane, cyclohexane, toluene, and pump oil indicated a separation efficiency of over 99 % for the types of mixtures tested together with excellent repeatability. In addition, the PDA and PA modified lignin-based foams were able to adsorb 67.1 mg/g of methylene blue, 96.1 mg/g of rhodamine B, and 98.2 mg/g of copper sulfate. The lignin-based foam could completely degrade under weak alkaline conditions after usage. This study highlighted a novel strategy for synthesizing environmentally friendly high-performance adsorbents to efficiently treat polluted wastewater using lignin as a raw material.

Bamboo charcoal fused with polyurethane foam for efficiently removing organic solvents from wastewater: experimental and simulation

Facile Preparation of Poly(melamine Formaldehyde) Sponge/bacterial Nanocellulose Composite for Oil-Water Separation

Preparation of biomass carbon/polyurethane foams for selective oil/water absorption

A Novel Application of Modified Bamboo Charcoal to Treat Oil-Containing Wastewater and Its Modified Mechanism.

Removal of Organic Pollutants in Solution by Bamboo Charcoal

Waste to treasure: Superwetting foam enhanced by bamboo powder for sustainable on-demand oil-water separation

Facilitate the preparation of naturally modified and self-healing superhydrophobic/superoleophilic biochar-based foams for efficient oil-water separation

Highly efficient oil-water separation and oil adsorption with hydrophobic hydrotalcite/polyurethane porous composite foam

Bamboo-Derived Low-Cost Mesoporous Biochar for Efficient Removal of Per- and Polyfluoroalkyl Substances from Contaminated Water

Mussel-Inspired and In Situ Polymerization-Modified Commercial Sponge for Efficient Crude Oil and Organic Solvent Adsorption

Multifunctional superhydrophilic/underwater superoleophobic lignin-based polyurethane foam for highly efficient oil-water separation and water purification

Preparation of Waterborne Polyurethane Foam with Active Carbon and Its Adsorption for Phenol in Aqueous Solution

Preparation of Biochar Composite Microspheres and Their Ability for Removal with Oil Agents in Dyed Wastewater

Efficient Removal of Pb(II) from Aqueous Solutions by Using Oil Palm Bio-Waste/MWCNTs Reinforced PVA Hydrogel Composites: Kinetic, Isotherm and Thermodynamic Modeling

Preparation of bio-based porous material with high oil adsorption capacity from bio-polyurethane and sugarcane bagasse

Durable superhydrophobic/superoleophilic melamine foam based on biomass-derived porous carbon and multi-walled carbon nanotube for oil/water separation

Biochars-Fe x PCu hybrides deriving from solid waste and waste acids for elimination of refractory organic pollutants from pharmaceutical wastewater

Adsorptive behaviors and mechanisms for removing three organic pollutants from aqueous solutions by polyvinyl alcohol/porous carbon composite hydrogels

Development of a new hydrophobic magnetic biochar for removing oil spills on the water surface

Lightweight, Mechanical Robust Foam with a Herringbone-Like Porous Structure for Oil/water Separation and Filtering

Biochar-based Asymmetric Membrane for Selective Removal and Oxidation of Hydrophobic Organic Pollutants.