Abstract:Superwettability can affect the performance of oil separation from water during the treatment of oily wastewater. Among various types of materials developed for cleaning oil pollution, foam is a popular choice due to its attractive lightweight properties and adjustable porosities. Foams with superwetting surfaces (superhydrophilic/superoleophobic underwater) are ideal for oil/water separations. In this study, lignin-based polyurethane foams (LPUFs) were synthesized first, and then polydopamine particles were deposited on the surface of the foam by in situ polymerization under weak alkaline conditions to increase its surface roughness. Afterwards, phytic acid was used to modify the foam to achieve surface superhydrophilicity and underwater superoleophobicity. Successful loading of polydopamine (PDA) particles and coating of phytic acid (PA) onto the foam was demonstrated by SEM, EDS, FTIR, XPS, and thermogravimetric analysis measurements. It was shown in the cyclic compression tests that LPUFs had good mechanical properties. Under 75 % compression strain, the maximum stress in the first cycle of LPUF/PDA/PA was 105.92 kPa. After 30 cyclic compression tests, the maximum stress of LPUF/PDA/PA under 75 % compression strain was 105.63 kPa, demonstrating a high mechanical stability. The contact angle of the foam modified by PDA and PA was 0° for water, 166.7° for chloroform, and 158.4° for hexane, which also demonstrated excellent underwater anti-oil adhesion performances. Oil-water separation tests by using PDA and PA modified lignin-based foam with mixtures of water and n -hexane, cyclohexane, toluene, and pump oil indicated a separation efficiency of over 99 % for the types of mixtures tested together with excellent repeatability. In addition, the PDA and PA modified lignin-based foams were able to adsorb 67.1 mg/g of methylene blue, 96.1 mg/g of rhodamine B, and 98.2 mg/g of copper sulfate. The lignin-based foam could completely degrade under weak alkaline conditions after usage. This study highlighted a novel strategy for synthesizing environmentally friendly high-performance adsorbents to efficiently treat polluted wastewater using lignin as a raw material.

Preparation of Waterborne Polyurethane Foam with Active Carbon and Its Adsorption for Phenol in Aqueous Solution

Efficient and rapid removal of typical phenolic compounds from water with biobased porous organic polymers

Preparation, Characterization, and Property Analysis of Environmentally Friendly Waterborne Polyurethane-Acrylate

Bamboo charcoal fused with polyurethane foam for efficiently removing organic solvents from wastewater: experimental and simulation

Comparison of Carbonized Materials from Wastes of Different Origin for Nonylphenol Removal by Adsorption

Multifunctional superhydrophilic/underwater superoleophobic lignin-based polyurethane foam for highly efficient oil-water separation and water purification

Adsorption treatment of phenolic wastewater by activated carbon:a review

A low-cost crosslinked polystyrene derived from environmental wastes for adsorption of phenolic compounds from aqueous solution

Design, Preparation, and Characterization of A Novel Hyper-Cross-Linked Polyphosphamide Polymer and Its Adsorption for Phenol

Preparation of biomass carbon/polyurethane foams for selective oil/water absorption

Removal of phenol by lignin-based activated carbon as an efficient adsorbent for adsorption of phenolic wastewater

Preparation and properties study of waterborne polyurethane synthesized by mixing polyester diols and isocyanates

Carboxylate-functionalized hollow polymer particles modified polyurethane foam for facile and selective removal of cationic dye

Efficient Separation of Per- and Polyfluoroalkyl Substances (PFAS) from Water by Aminated Polyacrylamide Hydrogel Foam

Enhanced Mechanical Properties and Functional Performances of Cationic Waterborne Polyurethanes Enabled by Different Natural Phenolic Acids

Catechol-Based Porous Organic Polymers for Effective Removal of Phenolic Pollutants from Water

Recyclable polyurethane foam loaded with carboxymethyl chitosan for adsorption of methylene blue

Pulverized Polyurethane Foam Particles Reinforced Rigid Polyurethane Foam And Phenolic Foam

Preparation and Characterization of Fluorinated Acrylate and Epoxy Co-Modified Waterborne Polyurethane

Preparation, mechanical properties of waterborne polyurethane and crosslinked polyurethane‐acrylate composite

Synthesis and characterization of non-ionic flame-retardant waterborne polyurethane