Abstract:Due to their superior stability and high open-circuit voltage (Voc), all-inorganic cesium lead bromine (CsPbBr3) perovskite solar cells are attractive for tandem device applications. However, the current methanol fabrication process requires multistep (at least 5–6 times) spin coating, which is tedious and time-consuming. Here, we introduced a modified two-step spin-coating method to prepare the CsPbBr3 films. Water, instead of methanol, has been selected as the solvent for CsBr. Via precisely controlling the loading time (t) of CsBr aqueous solution on the PbBr2 film surface, the prepared films can be tuned from a CsPbBr3@CsPb2Br5 phase (t < 15 s) to a well-crystallized CsPbBr3 phase (t ∼ 15 s) and finally the CsPbBr3@Cs4PbBr6 phase (t > 15 s). With a loading time of 15 s, we yield a maximum power conversion efficiency (PCE) of 9.14%, which is comparable with the devices fabricated from the methanol process. In addition, a high fill factor (FF) of 0.84 with a PCE of 9.02% has been obtained, which is among the highest FF reported for CsPbBr3 devices. Moreover, the devices hold superior stability with their PCEs slightly dropped under humidity and high temperature during a 30 day aging test. Overall, this facile and simple fabrication method reported in this work shows great potential for practical applications in the future.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c01593.Experimental methods along with additional information, including preheating temperature dependent J–V curves; XRD patterns of the CsPbBr3 films from the methanol process; SEM–EDX data; EDX mapping spectrum; AFM images of the loading time-dependent CsPbBr3 films; spin coating speed and precursor concentration dependent J–V characterization; J–V curve with the highest FF; hysteresis feature; photovoltaic parameters; defect density; and TRPL time constant (PDF)This article has not yet been cited by other publications.

A modified two-step sequential spin-coating method for perovskite solar cells using CsI containing organic salts in mixed ethanol/methanol solvent

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

Simultaneous Incorporation of CsI in the Two‐step Deposition Process Boosts the Power Conversion Efficiency and Stability of Perovskite Solar Cells

Synergistic Improvement of Perovskite Film Quality for Efficient Solar Cells Via Multiple Chloride Salt Additives

Boosting the efficiency and stability of CsPbBr3 perovskite solar cells through modified multi-step spin-coating method

Preparation of highly efficient and stable CsPbBr3 perovskite solar cells based on an anti-solvent rinsing strategy

Thiourea-Assisted Facile Fabrication of High-Quality CsPbBr3 Perovskite Films for High-Performance Solar Cells

A modified two-step sequential deposition method for preparing perovskite CH3NH3PbI3 solar cells

Bridging‐Solvent Strategy for Quasi‐Single‐Crystal Perovskite Films and Stable Solar Cells

Efficient Perovskite Solar Cells Fabricated Through CsCl-Enhanced PbI2 Precursor Via Sequential Deposition.

Application of Cesium on the Restriction of Precursor Crystallization for Highly Reproducible Perovskite Solar Cells Exceeding 20% Efficiency

Synergic Solventing-out Crystallization with Subsequent Time-Delay Thermal Annealing of PbI2 Precursor in Mesostructured Perovskite Solar Cells

Constructing Graded Perovskite Homojunctions by Adding Large Radius Phenylmethylamine Ions for Sequential Spin-Coating Deposition Method To Improve the Efficiency of Perovskite Solar Cells

A sustainable solvent system for processing CsPbBr<sub>3</sub> films for solar cells <i>via</i> an anomalous sequential deposition route

Controllable Blading Interdiffusion of Formamidinium Iodide on Thermal Evaporated Scalable and Conformal Lead Iodide for Efficient Perovskite Solar Cells

Heterogeneous Nucleation and Enhanced Charge Transfer via Amorphous Metal‐Organic Frameworks for Efficient and Stable Perovskite Solar Cells

Controllable Cosolvent Blade-Coating Strategy Toward Low-Temperature Fabrication of Perovskite Solar Cells

Ultra-smooth CsPbI2Br Film Via Programmable Crystallization Process for High-Efficiency Inorganic Perovskite Solar Cells

Improvement of Colloidal Characteristics in a Precursor Solution by a PbI2-(DMSO)2 Complex for Efficient Nonstoichiometrically Prepared CsPbI2.8Br0.2 Perovskite Solar Cells

Crystallization Kinetics Engineering toward High-Performance and Stable CsPbBr 3 -Based Perovskite Solar Cells

Methylammonium Chloride Additive in Lead Iodide Optimizing the Crystallization Process for Efficient Perovskite Solar Cells