Abstract:The preparation and tribological properties of PAI/PI‐EPN polymer coatings. To improve the tribological properties of polar crane copper alloy bearings to withstand wear under dry sliding wear and grease lubrication at low temperatures, three kinds of coating materials modified by incorporating WS2 and SiC into polyamide‐imide/polyimide‐phenolic epoxy resin were designed. These composite coatings were sprayed on the surfaces of CuPb22.5Sn2.5 copper alloys by liquid spraying technique. Firstly, the tribological experiments were performed with three different coatings. Then, nanoindentation testing and wear morphology analysis were conducted. The results show that the hardness of the composite coatings decreases with the increase of WS2. As the content of WS2 increases, the coefficients of friction (CoFs) of coatings decreases under dry sliding wear. The S2 coating filled with 7.5 wt% WS2 exhibits the lowest wear rate and the best wear resistance under low temperature and dry sliding wear. The coatings form a lubricating film on the worn surface under dry sliding wear at −70°C, improving the wear resistance of the coatings. The primary wear mechanisms are adhesive wear and fatigue wear. The wear rates of the coatings increase with the increasing content of WS2 under low‐temperature grease lubrication. The S1 coating filled with 5.0 wt% WS2 exhibits the lowest wear. The S1 coating demonstrates a CoF of 0.07 and a wear rate of 6.5 × 10−6 mm3N−1 m−1 at 0°C, showing excellent friction‐reducing and wear‐resistant properties. The primary wear mechanism is adhesive wear. The wear mechanisms of polymer coatings are closely related to temperature. The dominant wear mechanisms transfer from abrasive wear to adhesive wear and fatigue wear under dry sliding wear and decreasing temperature. The wear mechanisms transfer from predominantly adhesive and abrasive wear to adhesive wear, fatigue wear, and abrasive wear under grease lubrication. The hardness of the coatings and the behavior of the polymer at various low temperatures are the primary factors that affect the differing wear mechanisms.

A Study of the Properties of Polymer Coatings Based on an Organosilicon Material

Investigation of properties of polymer coatings based on organic-silicon material

Study of wear-resistance of anticorrosive organosilicon coatings under different operation condition

Investigation of the Wear Resistance of Anticorrosive Organosilicon Coatings under Various Operating Conditions

Friction and Wear Protection Performance of Synthetic Siloxane Lubricants

Development of silane/acrylate-based hybrid polymer coating through sol–gel technique for anti-corrosive application

Preparation of Silicone Coating and Its Anti-Ice and Anti-Corrosion Properties

Weather-Resistant Organosilicate Coatings with Improved Water Resistance

Modification of Epoxy Coatings with Fluorocontaining Organosilicon Copolymers

Polymer composites based on aromatic polyamide and fillers of spherical and layered structure for friction units of high-performance equipment

Tribological and Anticorrosion Behavior of Coating Systems Based on Polyurethane and Organic Silicon Compounds

The investigation of tribological properties of PAI/PI‐EPN polymer coating filled with WS2 and SiC at low temperatures

Comparative study on polysilazane and silicone resins as high-temperature-resistant coatings

Effect of silane coating surface treatment on friction and wear properties of carbon fiber/PI composites

Study on current-carrying friction and wear properties of copper-graphite brush material reinforced by organosilicon

Influence of silane treatment on the mechanical, tribological and morphological properties of corn stalk fiber reinforced polymer composites

THREE-DIMENSIONAL SETUP OF COMPOSITE MATERIALS AS A WAY TO ACHIEVE HIGH MECHANICAL PROPERTIES

Evaluation of mechanical properties and hydrophobicity of room‐temperature , moisture‐curable polysilazane coatings

Tribological Characteristics of a Friction Composition of Metal-Ceramic Powders and Carbon-Containing Additives on a Polymer Binder

In Situ Polymerization Approach to Graphene-Oxide-Reinforced Silicone Composites for Superior Anticorrosive Coating.

The Study of Composite Materials Properties Based on Polymers and Nano-Additives from Industrial Wastes from Kazakhstan