Abstract:Solar radiation is captured by photovoltaic (PV) panels, which use it to create electricity. However, an overabundance of photons striking the PV's surface raises its temperature, which lowers its efficiency. These days, cooling solar panels is very important, and research on these methods is widely available in the literature. Thus, the study field's problems truly lie in developing new or improved methods for doing the same tasks. The goal of this work is to further boost the efficiency of photovoltaic (PV) panels beyond what can be achieved with PCM and free/forced convection alone. To do this, phase change materials (PCM) are cooled using both free and forced convection. In accordance with the latitude of Lebanon's Bekaa Valley, four cooling techniques are experimentally investigated. A photovoltaic panel using phase-change material (PCM) with copper and aluminum wires in a 70 %–20 %–10 % mass ratio (CPCM-PV), respectively, is the first cooling method. In the second approach, four 5 cm long fins are fixed under free convection using the same combination of aluminum fins inside the PCM container while preserving the same ratio (IEF-PCM-Free-PV). The third technique is the same as the second but with forced convection (IEF-PCM-Forced-PV), while the fourth technique uses an aluminum finned plate with 16 finned plates under forced convection (F-Forced-PV). IEF-PCM-Forced-PV showed the most relative increases in efficiency rate of energy dissipated of 20.36 % and 62.24 %, respectively, as compared to the regular PV panel, according to the results. F-Forced-PV, IEF-PCM-Free-PV, and CPCM-PV showed an increase in relative efficiency of 16.87 %, 6.3 %, and 3.9 % respectively, and correspondingly, these enhancements were accompanied by an increase in energy dissipation of 55.80 %, 44.85 %, and 41.18 % for each system. Economically, the IEF-PCM-Forced-PV had the highest total yearly savings of $17.87 with a payback period of 1.9 years. An appropriate transient energy balance is conducted and permitted to demonstrate clearly the transient behavior of the system under the various cooling techniques. Finally, the percentage of enhancement using the newly suggested composite PCM with internal and external fins under forced convection is compared to the enhancement found in the literature for various classical techniques and shows greater potential for further enhancement of the PV performance.

Evaluation of thermal management of photovoltaic solar cell via hybrid cooling system of phase change material inclusion hybrid nanoparticles coupled with flat heat pipe

Impact of PCM type on photocell performance using heat pipe-PCM cooling system: A numerical study

Thermal evaluation of photovoltaic panels combined pulsating heat pipe with phase change materials: numerical study and experimental validation

Influence on solar PV performance integrated with heat sinks and nano-enhanced phase change material

A comprehensive experimental study of cooling photovoltaic panels using phase change materials under free and forced convection – Experiments and transient analysis

Photovoltaic Cooling Utilizing Phase Change Materials

Influence of Different Melting Points of Phase Change Material on Photovoltaic Phase Change Materials System Performance: An Energy, Exergy, and Environmental Point of View

Experimental Study on the Performance of a Solar Photovoltaic/thermal System Combined with Phase Change Material

Performance improvement of solar PV module through hybrid cooling system with thermoelectric coolers and phase change material

Impact of hybrid nano PCM (paraffin wax with Al 2 O 3 and ZnO nanoparticles) on photovoltaic thermal system: Energy, exergy, exergoeconomic and enviroeconomic analysis

Performance evaluation and thermal stabilization of photovoltaic panels using phase-change materials

Effect of varying the thermophysical properties of phase change material on the performance of photovoltaic/thermal-PCM hybrid module numerically

Parametric investigation of photovoltaic-thermal systems integrated with porous phase change material

A Parametric Study about the Potential to Integrate Phase Change Material into Photovoltaic Panel

Efficiency enhancement of photovoltaic module using bio-based eutectic phase change material: An experimental study

Photovoltaic Panel Cooling with New Composite of Phase Change Materials and Hierarchical Nanoparticles

Numerical investigation of the effect of operating conditions on performance of PV-PCM system

Thermo-economic Evaluation of PCM Layer Thickness Change on the Performance of the Hybrid Heat Storage Tank for Concentrating Solar Power Plants

Critical analysis of enhanced photovoltaic thermal systems: a comparative experimental study of PCM, TEG, and nanofluid applications

Performance enhancement of nanofluid-based photovoltaic/thermal system with a novel finned multi-block container of phase change material in the summer season of northern India

Thermal management of concentrator photovoltaic systems using nano‐enhanced phase change materials‐based heat sink