Abstract:The addition of trace (TiB + TiC) reinforcements could minimize the deformation steps and decreases its costs according to recent study. In present work, the hot deformation behavior and microstructure evolution were studied via the isothermal hot compression at different temperature and strain rate. Based on the DMM model, the activation energy Q and processing map were obtained. Subsequently, two billets were hot-rolled and heattreated, to study the microstructure and tensile properties of the alloy. Results revealed that the flow behavior of the (TiB + TiC)/Ti-3.5Al-5Mo-6V-3Cr-2Sn-0.5Fe alloy was similar with other near beta titanium alloy. When deformation in beta region, the deformation mechanism was associated with cDRX by lattice rotation and dynamic recovery; when deformation in (alpha + beta) region, the deformation mechanism was associated with substructure evolution, such as DRX and dynamic recovery. The lower strain rate guarantees abundant time for microstructure transformation, while the higher strain rate leads local flow instability and cracks. The activation energies Q is 264.1 kJ/mol in (alpha + beta) region and 181.8 kJ/mol in the beta region. According to the processing map, the optimum deformation windows are 770-800 degrees C and 850-880 degrees C, 0.001 s-1. In addition, the microstructure of 770R + SAT is characteristic of duplex microstructure with a certain amount of alpha p, considerable precipitation of fine acicular alpha s and continuous alpha GB, which is achieved a UTS of 1414 MPa with a poor ductility. Therefore, the (TiB + TiC)/ Ti-3.5Al-5Mo-6V-3Cr-2Sn-0.5Fe alloy shows excellent deformability and higher strength, which is possible to achieve both high economy (less deformation step) and advancement (high mechanical properties due (TiB + TiC) reinforcements).

Microstructure and tensile properties of a multi-alloyed α + β titanium alloy Ti4.5Al10.5V3Fe

Design and Preparation of Low-Cost Α + Β Titanium Alloy Based on Assessment of Ti-Al-Fe-Cr System

Microstructure and Mechanical Properties of Novel Ti-Al- Mn- W Alloy

Electron Beam Welding and Post Heat Treatment of a New Near-Beta High-Strength Ti-4Al-5Mo-5V-5Cr-1Nb Alloy

Microstructures and Tensile Properties of a High Strength Β Titanium Alloy Ti5Al4Zr8Mo7V by Near Β Forging and Β-Transus Forging

Design and microstructure-mechanical properties of a novel metastable β titanium alloy with excellent strength-plasticity matching

Alloying Design of Titanium Aluminum Intermetallics and Research Progress

Research on the microstructure and properties of metastable β type Ti-8V4Mo3Cr3Zr3Al alloy with high strength and toughness

The Microstructure, Mechanical Properties, and Corrosion Resistance of a Novel Extruded Titanium Alloy

Microstructure evolution and mechanical properties of a novel beta γ-TiAl alloy

Development of a Low-Density and High-Strength Titanium Alloy

Compositional and Microstructural Optimization and Mechanical-Property Enhancement of Cast Ti Alloys Based on Ti-6Al-4V Alloy

Study on the Relationship Between Microstructure and Mechanical Property in a Metastable Β Titanium Alloy

Forging–microstructure–tensile properties correlation in a new near β high-strength titanium alloy

Face Centered Cubic Substructure and Improved Tensile Property in a Novel Β Titanium Alloy Ti–5Al–4Zr–10Mo–3Cr

Microstructure evolution, mechanical properties and high temperature deformation of (TiB + TiC)/Ti-3.5Al-5Mo-6V-3Cr-2Sn-0.5Fe titanium alloy

Microstructure, Mechanical Properties, Hot Deformation and Oxidation Behavior of Ti–45Al–5.4V–3.6Nb–0.3Y Alloy

A new α + β Ti-alloy with refined microstructures and enhanced mechanical properties in the as-cast state

Microstructure, Mechanical Properties and Deformation Behavior of New V-free Low-Cost Ti-6Al-xFe-yCr Alloys

Relationship Between Microstructure and Tensile Properties on a Near-Β Titanium Alloy after Multidirectional Forging and Heat Treatment

Improvement of microstructure and mechanical properties of TiAl?Nb alloy by adding Fe element