Abstract:College of Engineering, Design and Physical Sciences Doctorate of Philosophy By Sina Fateri Ultrasonic technology is commonly used in the field of Non-Destructive Testing (NDT) of metal structures such as steel, aluminium, etc. Compared to ultrasonic bulk waves that travel in infinite media with no boundary influence, Ultrasonic Guided Waves (UGWs) require a structural boundary for propagation such that they can be used to inspect and monitor long elements of a structure from a single position. The greatest challenges for any UGW system are the plethora of wave modes arising from the geometry of the structural element which propagate with a range of frequency dependent velocities and the interpretation of these combined signals reflected by discontinuities in the structural element. In this thesis, a technique is developed which facilitates the measurement of Time of Arrival (ToA) and group velocity dispersion curves of wave modes for one dimensional structures as far as wave propagation is concerned. A second technique is also presented which employs the dispersion curves to deliver enhanced range measurements in complex multimodal UGW responses. Ultimately, the aforementioned techniques are used as a part of the analysis of previously unreported signals arising from interactions of UGWs with piezoelectric transducers. The first signal processing technique is presented which used a combination of frequency-sweep measurement, sampling rate conversion and the Fourier transform. The technique is applied to synthesized and experimental data in order to identify different wave modes in complex UGW signals. It is demonstrated that the technique has the capability to derive the ToA and group velocity dispersion curve of the wave modes of interest. The second signal processing technique uses broad band excitation, dispersion compensation and cross-correlation. The technique is applied to synthesized and experimental data in order to identify different wave modes in complex UGW signals. It is demonstrated that the technique noticeably improves the Signal to Noise Ratio (SNR) of the UGW response using a priori knowledge of the dispersion curve. It is also able to derive accurate quantitative information about the ToA and the propagation distance. During the development of the aforementioned signal processing techniques, some unwanted wave-packets are identified in the UGW responses which are found to be induced by the coupling of a shear mode piezoelectric transducer at the free edge of the waveguide. Accordingly, the effect of the force on the piezoelectric transducers and the corresponding reflections and mode conversions are studied experimentally. The aforementioned signal processing techniques are also employed as a part of the study. A Finite Element Analysis (FEA) procedure is also presented which can potentially improve the theoretical predictions and converge to results found in experimental routines. The approach enhances the confidence in the FEA models compared to traditional approaches. The outcome of the research conducted in this thesis paves the way to enhance the reliability of UGW inspections by utilizing the signal processing techniques and studying the multimodal responses.

A Review of Signal Processing Techniques for Ultrasonic Guided Wave Testing

Evaluation of Pipe Axial Defeat Through the Use of Ultrasonic Guided Wave and Matching Pursuit

Ultrasonic Guided Wave-Based Circumferential Scanning of Plates Using a Synthetic Aperture Focusing Technique

Nondestructive Evaluation of Special Defects Based on Ultrasound Metasurface

Implementing Ultrasonic Guided Wave Mode Control in Hollow Cylinders

Review of Current Guided Wave Ultrasonic Testing (GWUT) Limitations and Future Directions

Ultrasonic guided wave techniques and applications in pipeline defect detection: A review

Detection, Localisation and Assessment of Defects in Pipes Using Guided Wave Techniques: A Review

Advanced signal processing techniques for multimodal ultrasonic guided wave response

Application Research of Ultrasonic-Guided Wave Technology in Pipeline Corrosion Defect Detection: A Review

Acoustoelastic Guided and Surface Waves in Waveguides with Focus on Non-Destructive Testing and Structural Health Monitoring Applications —A Review of Recent Studies

Contemporary ultrasonic signal processing approaches for nondestructive evaluation of multilayered structures

A Systematic Review of Ultrasonic Techniques for Defects Detection in Construction and Building Materials

Experimental Study of Static and Dynamic Loading Effects on Guided Wave-Based Intelligent Monitoring of Welded Rail Joints

A Review of Ultrasonic Testing Applications in Spot Welding: Defect Evaluation in Experimental and Simulation Results

An Inspection Technique for Steel Pipes Wall Condition Using Ultrasonic Guided Helical Waves and a Limited Number of Transducers

Defect detection and localisation using guided wave images from array data processed by nonlinear autoregressive exogenous model and Gamma statistical operator

A review of synthetic and augmented training data for machine learning in ultrasonic non-destructive evaluation

A review of ultrasonic testing applications in additive manufacturing: Defect evaluation, material characterization, and process control

Optical methods of laser ultrasonic testing technology in the industrial and engineering applications: A review

Ultrasonic Guided-Waves Sensors and Integrated Structural Health Monitoring Systems for Impact Detection and Localization: A Review