Abstract:To alleviate the shortage of river sand (RS) and recycle abandoned resources, two recycled manufactured sands (RMSs) produced from tunnel excavation rock (tuff manufactured sand, TS) and granite cutting waste (granite manufactured sand, GS) are studied and compared with standard sand (SS) and RS. The aim is to identify the application potential of the two RMSs in cement-based materials. This is done by analyzing their influences on the mortar properties based on their surface characteristics and establishing a correlation between the surface characteristics of RMS and mortar properties. For the parent rock, petrographic analysis is performed and the uniaxial compressive strength is measured. For sand, the physical properties are evaluated and X-ray diffraction is used for analyzing the chemical composition. Digital image processing, nitrogen adsorption, and X-ray computed tomography are employed to determine the surface characteristics of sand particles. For the mortar, the fluidity, mechanical strength, water absorption, early total shrinkage, and accelerated expansion ratio are measured. The microstructure of the mortar interface transition zone is examined. Mercury intrusion porosimetry and thermogravimetric analysis are conducted to study the internal mechanism. The results indicate that compared with SS, the two RMSs reduce the fluidity of fresh mortar. In addition, TS is beneficial for the flexural, compressive, and tensile strengths of hardened mortar because of its denser internal pore structure and high degree of hydration caused by the properties of sand. The mechanical strength of the GS mortar can reach a similar or slightly higher level than that of the SS mortar. Furthermore, the fluidity and mechanical strength are well correlated with two parameters of sand, namely, roundness and specific surface area. The tensile strain capacity of the RMS-based mortar is superior to those of the SS and RS mortars. However, RMS increases the early total shrinkage. Although the TS mortar has the highest tensile strain capacity, it also has the largest early total shrinkage among the four mortar mixtures. Comparing the escalations in tensile strain capacity and early total shrinkage, the TS increases the risk of shrinkage cracking in the early stages. The effect of GS on the mortar tensile strain capacity is slightly greater than that on the early total shrinkage; thus, there is no significant influence on the risk of early shrinkage cracking in the GS mortar. In the accelerated expansion test, the TS shows potential alkali-silica reaction (ASR) risk in accordance with ASTM C1260, however, the GS indicates no potential for expansion damage. Based on the performance of various sands and mortars, GS has a better application value than TS. As for the TS mortar, it is necessary to consider the shrinkage cracking risk and ASR hazard in practical applications.

Improving the Performance of Cement Mortar Using Granite Powder and Nano-Silica

The Synergy Effect of Limestone Powder and Mineral Admixtures on the Mechanical Property of Mortar

Granite Powder vs. Fly Ash for the Sustainable Production of Air-Cured Cementitious Mortars

Application Potential of Granite Cutting Waste and Tunnel Excavation Rock As Fine Aggregates in Cement-Based Materials Based on Surface Characteristics

Utilization of nanoparticles and waste materials in cement mortars

Enhancing Mechanical Properties and Microstructures of Mass-Manufactured Sand Concrete by Incorporating Granite Powder

Assessment of the Mechanical Properties of High Strength Mortar Incorporating Silica Fume and Graphene Nanoplatelets: Experimental and Mathematical Modeling

Manufacturing nano novel composites using sugarcane and eggshell as an alternative for producing nano green mortar

Feasibility of stone slurry powder and admixtures in cement mortar

Enhanced early hydration and mechanical properties of cement-based materials with recycled concrete powder modified by nano-silica

Development of Mortars That Use Recycled Aggregates from a Sodium Silicate Process and the Influence of Graphene Oxide as a Nano-Addition

Combined Effect of Nano Ferrite and Nano Silica onProperties of Cement Mortar

Mechanical Properties and Durability Performance of Concrete Containing Calcium Carbide Residue and Nano Silica

Influence of synthesized nanomaterials in the strength and durability of cementitious composites

Effects of Al2O3, SiO2 nanoparticles, and g-c3n4 nanosheets on biocement production from agricultural wastes

Influence of silicon-dioxide nanoparticles in cementitious mortars: verification using X-ray diffraction, thermal analysis, physical, and mechanical tests

Influence of recycled concrete, marble, glass, and limestone powder, and utilization ratios on the compressive strength and alkali–silica reaction performance of mortar mixtures

Experimental investigation on the effect of incorporating nanomaterials on some properties of self-compacting cementitious mortar

Enhancement of concrete performance via mixed limestone and granite powders

Effect of nano materials on cementitious mortar composites exposed to sulphate attack