Abstract:The complex three-shaft three-reducer structural designs of helicopter transmission systems are prone to changes in the relative positions of shafting under the conditions of main rotor and tail rotor loads. These changes will affect the transmission characteristics of the entire transmission system. In this study, the planetary gear trains of helicopters were examined. Due to the fact that these structures are considered to be the most representative structures of the main reducers of helicopters, they were selected as the study objects for the purpose of examining the meshing characteristics of planetary gear trains when the relative positions of the shafting changed due to the position changes of the main rotor shafts under variable load conditions. It was found that by embedding the comprehensive time-varying meshing stiffness values of the main rotor shafts at different positions, a dynamic model of the relative position changes of the planetary gear trains could be established. Then, combined with the multibody dynamics software, the meshing characteristics of the sun gears, and the planetary gears, the planetary gears and the inner ring gears were simulated and analyzed under different inclinations and offsets of the shafting. The results obtained in this study revealed the following: (1) the average meshing force of the gears increased with the increases in the angle inclinations, and the meshing force between the sun gears and the planetary gears increased faster than the meshing force between the planetary gears and the inner ring gears. It was observed that during the changes in the shafting tilt positions, obvious side frequency signals had appeared around the peak of the meshing frequency in the spectrum. Then, with the continuous increases in the tilt position, the peak was gradually submerged; (2) the average meshing force of the gears increased with the increases in the offset, and the increasing trend of the meshing force between the sun gears and the planetary gears was similar to that observed between the planetary gears and the inner ring gears. It was found that when the shafting offset position changed, there were obvious first and second frequency doubling in the spectrum; (3) the mass center orbit radii of the sun gears increased with the increases in the shafting position changes, and the changes in the angular tilt position were found to have greater influencing effects on the mass center orbit radii of the sun gears than the changes in the offset positions. This study’s research findings will provide a theoretical basis for future operational status monitoring of the main transmission systems of helicopters and are of major significance for improvements in the operational stability of helicopter transmission systems, which will potentially ensure safe and efficient operations.

Study on the Tooth Profile Parameters Design Method of Crown Gear Coupling for Helicopter Tail Folding Device

Quasi-static Tooth Contact Analysis of Hypoid Gear Drive with Coaxiality Deviations

Optimization design of load-sharing and light weight of the twin rotors concentric face gear power-split transmission system based on gear tooth matching condition

Modeling and dynamic analysis of spiral bevel gear coupled system of intermediate and tail gearboxes in a helicopter

Optimizing circumferential assembly angle of rotor parts connected by curvic couplings based on acquired tooth surface error data

Parameter design of double-circular-arc tooth profile and its influence on meshing characteristics of harmonic drive

Tooth Profile Modification of Helical Gears and Experimental Study Based on Finite Element Contact Analysis

A modeling and tooth contact analysis method of parabolic modified face gear

An Analysis of the Gear Meshing Characteristics of the Main Planetary Gear Trains of Helicopters Undergoing Shafting Position Changes

Optimal calculation and experimental study on cutting force of low-angle straight tooth face gear by power skiving

Computational Optimization of the Basic Data and Tooth Form Parameters Based on the Contact Strength for Hypoid Gear

Influence of different combinations of high-order topological modification on contact pattern and load distribution of helical gear

Parametric modeling and contact analysis of helical gears with modifications

Tooth surface geometry optimization of spiral bevel and hypoid gears generated by duplex helical method with circular profile blade

Precise modeling of complex tooth surface microtopography and multi-degree-of-freedom nonlinear friction dynamics for high-performance face gear

Parametric analysis of tooth surface characteristics of flexspline in harmonic reducer after hobbing

Geometric design and analysis of face-gear drive with involute helical pinion

Tooth surface mismatch design of cycloidal bevel gear based on two directions modification of pinion cutter

A Novel Tooth Surface Modification Methodology for Wide-Faced Double-Helical Gear Pairs

Improved algorithm of tooth surface topological modification and nonlinear dynamic analysis of herringbone gears

Double-circular-arc tooth profile design and parametric analysis on the comprehensive performance of the harmonic drive