Abstract:As a promising cathode material for lithium–sulfur (Li-S) batteries, sulfurized polyacrylonitrile (SPAN) with uniform dispersion of short-chain sulfur moieties on its organic skeletons can effectively avoid lithium polysulfides dissolution and exhibit high specific capacity and long-term cycling stability. However, the practical battery performance of the SPAN cathode is dramatically limited by its relatively poor ionic and electronic accessibility. In this work, a three-dimensional (3D) network of Se0.05S0.95PAN nanofibers incorporated with commercial and low-cost Ketjen black (KB), denoted as 0.05S0.95PAN, is prepared through the electrospinning method. This unique 3D nanofiber structure is beneficial to transport lithium ions and electrons and accommodate volume expansion during lithiation/delithiation processes for Li-S batteries, leading to tremendous improvement of sulfur utilization, rate capability, and long-term cycling performance. 0.05S0.95PAN exhibits an ultrahigh reversible capacity of 1491 mAh g–1 at 0.1C and 1130 mAh g–1 at 5C and retains 1224 mAh g–1 after 500 cycles at 1C, corresponding to a capacity retention of 96.4%. This work proposes a facile strategy for the preparation of sulfur cathodes applicable in lithium–sulfur batteries.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.2c00585.Material preparation, material characterization, electrochemical measurements, SEM images of the ES-PAN fiber and fiber, elemental analysis data table, XPS spectrum of 0.05S0.95PAN, cycling performance of the 0.05S0.95PAN cathode at 0.5C, rate performance of 0.05S0.95PAN at different rates, CV curves of 0.05S0.95PAN and ES-Se0.05S0.95PAN at different rates and linear fit, HR-SEM images and EDS element mappings of 0.05S0.95PAN after cycling, XPS spectrum of the 0.05S0.95PAN cathode after cycling, SEM images of the 0.05S0.95PAN cathode before/after cycling, and comparison of the previous report (PDF)This article has not yet been cited by other publications.

An in-situ catalytic-insoluble strategy enabled by sulfurized polyacrylonitrile-based composite cathode for potassium–sulfur batteries

Encapsulating segment-like antimony nanorod in hollow carbon tube as long-lifespan, high-rate anodes for rechargeable K-ion batteries

Feasible Catalytic-Insoluble Strategy Enabled by Sulfurized Polyacrylonitrile with In Situ Built Electrocatalysts for Ultrastable Lithium–Sulfur Batteries

Bio-derived N-doped Porous Carbon As Sulfur Hosts for High Performance Lithium Sulfur Batteries

Flexible CNT-Interpenetrating Hierarchically Porous Sulfurized Polyacrylonitrile (CIHP-SPAN) Electrodes for High-Rate Lithium-Sulfur (Li-S) Batteries

Free-standing, flexible and stable potassium–sulfur battery enabled by controllable porous carbon cloth

Electrospun Sulfurized Polyacrylonitrile Nanofibers for Long-Term Cycling Stability and High-Rate Lithium–Sulfur Batteries

Sulfurization accelerator coupled Fe1−xS electrocatalyst boosting SPAN cathode performance

Enhancing the performance of a lithium-sulfur battery with spatially confined mesoporous nanoreactors in sulfurized polyacrylonitrile cathodes

Sulfurization accelerator coupled Fe 1− x S electrocatalyst boosting SPAN cathode performance

Sulfurization accelerator coupled Fe<sub>1-<i>x</i></sub>S electrocatalyst boosting SPAN cathode performance

Facile synthesis of sulfurized polyacrylonitrile composite as cathode for high-rate lithium-sulfur batteries

Unraveling the mechanism on improved kinetics performance of sulfurized polyacrylonitrile with defective conductive carbon matrix

Scalable SPAN Membrane Cathode with High Conductivity and Hierarchically Porous Framework for Enhanced Ion Transfer and Cycling Stability in Li–S Batteries

High-Performance Stable Potassium–Sulfur Batteries Enabled by Free-Standing CNT Film-Based Composite Cathodes

Sulfur Nanocomposite As a Positive Electrode Material for Rechargeable Potassium-Sulfur Batteries.

Electrochemical Enhancement of Lithium‐Ion Diffusion in Polypyrrole‐Modified Sulfurized Polyacrylonitrile Nanotubes for Solid‐to‐Solid Free‐Standing Lithium–Sulfur Cathodes

Multiscale Understanding of Covalently Fixed Sulfur–Polyacrylonitrile Composite as Advanced Cathode for Metal–Sulfur Batteries

Solid-State Transformations of Active Materials in the Pores of Sulfurized-Polyacrylonitrile Fiber Membranes via Nucleophilic Reactions for High-Loading and Free-Standing Lithium–Sulfur Battery Cathodes

Strategy for High-Energy Li-S Battery Coupling with a Li Metal Anode and a Sulfurized Polyacrylonitrile Cathode

Optimizing potassium polysulfides for high performance potassium-sulfur batteries