Abstract:A self-assembled MoS2/Mo-S-C multilayer film prepared by r.f. co-sputtering of MoS2 and graphite targets was tribotested in diverse sliding atmospheres, and the lubricant mechanism and its correlations to the selective releasing behavior of non-lubricant component were analyzed in detail. Based on the analysis of composition and structural transformation of transferred materials by Raman and HRTEM characterizations, selective releasing behavior according to the sliding atmospheres were found to be particularly apparent in vacuum and dry inert atmospheres. Under these conditions, a-C in graphitic form was selectively released outwards from the topmost surfaces of contacts, leaving MoS2 layers finely reordered in (002) orientation playing a lubricant role. Composition and structural transformation were observed not only on the topmost surface of wear track but also on the underlying layer at a thickness of tens of nanometers. Moreover, it was found that the selective releasing of a-C initiated from the center of contacts with higher pressure, and then developed toward the edges, resulting in a gradual change in the composition and microstructure of the transferred materials from the well-aligned MoS2 layers in the center to the graphitic a-C dominant composites at the edges. The short running-in periods and low-friction performance in all the tribotests suggested that the initial preference of MoS2-riched sublayers in (002) orientation may facilitate the formation of shearless tribofilms and therefore provide a feasible way of structural tailoring in the MoS2-based lubricant films for an improved triboactive response.

Features of Sliding Friction on Thin-Film Mo–S–C Coatings Prepared by Pulsed Laser Deposition

Component selection and nano-structuring of WS2/MoS2/a-C thin-film coatings for effective friction reduction in difficult conditions of sliding

Reactive Pulsed Laser Deposition of Clustered-Type MoSx (x ~ 2, 3, and 4) Films and Their Solid Lubricant Properties at Low Temperature

Microstructure and dry sliding wear behavior of MoS2/TiC/Ni composite coatings prepared by laser cladding

Dry Wear Behaviors of Wear Resistant Composite Coatings Produced by Laser Cladding

Influence of C Dopant on the Structure, Mechanical and Tribological Properties of R.F.-Sputtered Mos2/A-C Composite Films

Structure and properties of molybdenum-disulfide/amorphous carbon composited coatings deposited by co-sputtering method

Friction and wear properties of CrSiCN coatings with low carbon content as sliding against SiC and steel balls in water

Friction and wear performance of electrospark deposited Ni/C-MoS2 self-lubricating coating

Micro-structural, electrical, and tribological properties of SiC/DLC composite coating grown by PLD on steel

Microstructure and Friction–Wear Performance of Laser Cladded Cu10Al–Ti–MoS2 Coatings Under Oil Lubrication Condition

Microstructure Characteristics and Tribological Properties of Gradient Cu-MoS2 Self-Lubricating Coating Fabricated by Selective Laser Melting of Ink-Printed Metal Nanoparticles

Enhancement of Friction Performance of Fluorinated Graphene and Molybdenum Disulfide Coating by Microdimple Arrays

Study on microstructure and wear behaviors of MoS2/TiC/Ni composite wear-resistant coating by laser cladding

Selective-releasing-affected Lubricant Mechanism of a Self-Assembled MoS2/Mo-S-C Nanoperiod Multilayer Film Sliding in Diverse Atmospheres.

Friction Properties of Cr_3C_2-Ni Coatings Prepared by Laser Cladding

Tribological investigation of MoS 2 coatings deposited on the laser textured surface

Compaction of Hydrophobic Molybdenum Disulfide Coatings for Promoting Tribological Behaviors on Engineering Steel

Preparation and tribological properties of Mo/MoS2-Pb-PbS composite films

Impact Fretting Wear of MoS2/C Nanocomposite Coating with Different Carbon Contents under Cycling Low Kinetic Energy

Surface Composition–lubrication Design of Al2O3/Ni Laminated Composites – Part II: Tribological Behavior of LaF3-doped MoS2 Composite Coating in a Water Environment