Abstract:Enhancing inlet gas temperature in aero/gas turbines to reduce their carbon-footprint, has led to a strive for better performing inlet cooling mechanism of the turbine blades. The internal cooling of the blades is made by ceramic cores in their casting process, but conventional ceramic molding has long reached its maximum possible geometrical complexity, hence shedding light on 3D printing of these cores. The objective of this study is to develop low-viscous, fully stabilized, commercially viable ink for vat-photopolymerization of silica-based ceramics. This paper investigates the best dispersion type and amount for different formulated monomer mixtures, and explains the best correlation between viscosity, solid loading, binders, dispersants, peeling forces and mechanical properties, and offers an optimized mixture to avoid the common ceramic printing issue, namely crack propagation of cores during sintering. Among five dispersant agents, the SOL20, SOL24 and FA4611 exhibited better performance than other dispersion agents, and the optimum concentration level for each binder and dispersant agent was ensured through sedimentation test. Their dispersion capability and long-term stability were further investigated to designate the best dispersion agent for each binder system. Further verification was made by sedimentation study of the samples at 40 °C for 40 days and reducing the superficial area of the used powder mixture. According to the result of the rheology analysis, the best dispersions were achieved using SOL20 for the loaded binder mixtures of M1 and M4, SOL24 for M3and FA4611 for M2. The instability of M1 and M2 with their respective dispersant agent was coordinated through the thixotropic agent of TX/2, and complete stabilization and near-Newtonian behavior were achieved. However, the research showed that the addition of TX/2 to fully stabilized M4 and M2 suspensions negatively impacts the mixtures' rheological behavior from near-Newtonian to shear-thickening. In the final stage of this study, peeling forces, sintering and three-point bending tests were conducted to determine the final formulated suspension to print ceramic core components. M4 and SOL20 combination was selected for SiO 2 -ZrSiO 4 loading and dispersing, respectively. The impact of solid loading between the range of 58 and 65 vol.% on the rheological behavior of the final suspension and the mechanical properties of sintered bodies were investigated to assign an optimum solid rate. The adequate strength on sintered and degree of viscosity for ceramic vat-polymerization processing was achieved at 58 vol.%. Lastly, a validation study is conducted by printing a complex ceramic core model by a commercial LCD hobby printer. This validation shows the significance of this study to scale up the manufacturing of complex-shaped ceramic cores and to revolutionize the sector, by printing inexpensive and readily available irregular-shaped (non-atomized) ceramic powder, using the most cost-effective LCD printers (non-specialized expensive ceramic printers).

Tailoring α-alumina powder morphology through spray drying for cold consolidation by binder jetting

Tailoring hydroxyapatite microspheres by spray-drying for powder bed fusion feedstock

Influence of Different Powder Conditioning Strategies on Metal Binder Jetting with Ti-6Al-4V

Effect of the Particle Size Distribution of Irregular Al Powder on Properties of Parts for Electronics Fabricated by Binder Jetting

Influence of Alumina Grade on Sintering Properties and Possible Application in Binder Jetting Additive Technology

Preparation and characterization of Cr 2 AlC microspheres prepared by spray-drying granulation

Spray Freeze Granulation of Submicron Alumina and Its Sintering Behavior Via Spark Plasma Sintering

Effect of dispersant and binder on the morphology of zirconia granules during spray drying

Enhancing powder bed fusion of alumina ceramic material: a comprehensive study from powder tailoring to mechanical performance evaluation

Evaluation of Different Sintering Agents for Binder Jetting of Aluminum Alloy

Binder stabilization and rheology optimization for vat-photopolymerization 3D printing of silica-based ceramic mixtures

Characterisation of gas-atomised metal powders used in binder jet 3D printing

Tailoring green and sintered density of pure iron parts using binder jetting additive manufacturing

Surface Treatment and Modification of Al2O3 Powders

Development of a manufacturing process for Binder Jet 3D printed porous Al2O3 supports used in heterogeneous catalysis

Analysis of the Nanoparticle Dispersion and Its Effect on the Crystalline Microstructure in Carbon-Additivated PA12 Feedstock Material for Laser Powder Bed Fusion

Tailoring Dry Microparticles for Pulmonary Drug Delivery: Ultrasonic Spray Freeze-Drying with Mannitol and Salbutamol Sulphate

Removal of Stair-Step Effects in Binder Jetting Additive Manufacturing Using Grayscale and Dithering-Based Droplet Distribution

Effect of Particle Size Distribution on Powder Packing and Sintering in Binder Jetting Additive Manufacturing of Metals

Tailoring metal powders by dry nanoparticle coating for powder bed fusion applications

Rheological properties and spray-drying behaviors of nano-SiC based aqueous slurry