Abstract:Laser metal-wire deposition (LMwD) exhibits a larger molten pool and layer height during printing, compared to powder bed fusion additive manufacturing; in the present study, these features revealed a more inhomogeneous but easily observable microstructure. The coaxial double laser used herein makes the energy distribution of the molten pool more complex than that afforded by a single laser source, and the microstructure of the LMwD parts was more heterogeneous as well. We observed the microstructure of Ti6Al4V by the double LMwD as-built samples by conducting a laboratory experiment and a simulation. The precipitated martensite (α') phase was defined after eliminating the influence of the β element in an X-ray diffraction analysis, which has not been discussed previously in the literature. We also propose a theory regarding the formation of heat-affected zone (HAZ) bands in an environment that includes the α' phase. Our experiments revealed only white HAZ bands, which can be attributed to the solute partitioning caused by sequential thermal cycling and the absence of the β element. The microhardness of the HAZ band areas was lower than that of both the upper and lower sides. The simulation results indicate that the maximum temperature of 2925 °C restrains the generating of HAZ bands in the final two deposited layers, due to its great difference from the β transus temperature. Moreover, the higher heat accumulation in the upper layers promoted the migration of β-grain boundaries, which may explain why the coarse columnar β grains tended to grow at the edge area in the layers deposited later. We also observed that with the use of high temperature, the nucleation of β grains is more easily promoted in the lower layers. We conclude that the concentration of residual stress in the fusion zone and the first layer is favorable to the nucleation of equiaxed grains.

Geometrical study of 5356 aluminium alloy by means of a concentric wire laser metal deposition

Additively Manufactured Al/SiC Cylindrical Structures by Laser Metal Deposition

Studying the layer structure formation in laser additive manufacturing with AlMg6 alloy wire

Low-Defect AM of High Strength Aluminium Alloy by LMD

Laser Metal Deposition of Ti6Al4V—A Brief Review

Sustainable laser metal deposition of aluminum alloys for the automotive industry

Improving the deposition efficiency and mechanical properties of additive manufactured Inconel 625 through hot wire laser metal deposition

Wire Laser Metal Deposition Additive Manufacturing of Duplex Stainless Steel Components—Development of a Systematic Methodology

Microstructure and Microhardness of High-Strength Aluminium Alloy Prepared Using High-Speed Laser Fabrication

Wire-Arc Directed Energy Deposition of Aluminum Alloy 7075 with Dispersed Nanoparticles

Effect of Interlayer Cooling Time, Constraint and Tool Path Strategy on Deformation of Large Components Made by Laser Metal Deposition with Wire

Investigation of the Microstructure of Ti6Al4V Alloy by Coaxial Double Laser Metal-Wire Deposition

Microstructures and Properties of Al-Mg Alloys Manufactured by WAAM-CMT

Additive manufacturing of Ti-6Al-4V alloy by micro-laser metal wire deposition with pulsed wave emission: processability and microstructure formation

Nanotwins-containing microstructure and superior mechanical strength of a Cu‒9Al‒5Fe‒5Ni alloy additively manufactured by laser metal deposition

Additive Manufacturing of Ti6Al4V with Wire Laser Metal Deposition Process

Densification, Microstructure, and Mechanical Properties of Additively Manufactured 2124 Al–Cu Alloy by Selective Laser Melting

Wire Arc Additive Manufacturing (WAAM) of Aluminum Alloy AlMg5Mn with Energy-Reduced Gas Metal Arc Welding (GMAW)

Highly-efficient additive manufacturing of Inconel 625 thin wall using hot-wire laser metal deposition: Process optimization, microstructure, and mechanical properties

Methodology for Designing a Laser-Based Additive Process for the Formation of a Lattice Periodic Structure on the Surface of an Aluminum Alloy Plate

Review on Laser Directed Energy Deposited Aluminum Alloys