Abstract:The existing methods of preparing lightweight gypsum blocks are to make hollow slats or to make foamed blocks, both of which are defective and fail to meet the standards. In order to prepare lightweight gypsum blocks, this paper investigates the method of increasing the proportion of moisture to reduce the weight of gypsum blocks. To further understand the performance relation between β-hemihydrate gypsum (β-hemihydrate phosphogypsum and β-hemihydrate flue-gas desulfurization gypsum) and its products, the effect of borax on the hydration and hardening of β-hemihydrate gypsum at high water–plaster ratio was studied. The results showed that with an increase in borax dosage, the setting time of β-hemihydrate phosphogypsum (β-HPG) was evidently prolonged; the initial setting time increased from 15 to 62 min, and the final setting time increased from 22 to 93 min. The difference between the initial and final setting times also increased, and the fluidity of the gypsum slurry was improved. When the borax dosage reached 0.5%, the flexural strength of β-hemihydrate flue-gas desulfurization gypsum (β-HFGD) increased from 5.2 to 6.3 MPa and the compressive strength increased from 4.7 to 9.3 MPa after 28 d. By analyzing the changes in phase transition, hydration degree, infrared spectrum, particle size, and crystal microstructure during the hydration of β-hemihydrate gypsum, it was found that β-HPG was more sensitive to borax than β-HFGD at high water–plaster ratio and β-HFGD showed superior mechanical properties. The study findings will provide a theoretical basis for the application of β-hemihydrate gypsum products under humid conditions and expand the application range of gypsum products.

Effect of borax on the hydration and setting of magnesium phosphate cements

Function and effect of borax on magnesium phosphate cement prepared by magnesium slag after salt lake lithium extraction

Study on the hydration process and borax retarding mechanism of the magnesium ammonium phosphate cement-based coating system

Effect of seawater on hydration of magnesium potassium phosphate cements

Combined effect of NaAlO2 and NaOH on the early age hydration of Portland cement with a high concentration of borate solution

Thermodynamic modeling of magnesium ammonium phosphate cement and stability of its hydration products

Effects of Bauxite Tailings and Sodium Silicate on Mechanical Properties and Hydration Mechanism of Magnesium Phosphate Cement

Effect of Magnesium-containing Modifier on the Properties of Boron Aluminum Phosphate Inorganic Binder and Its Heat-cured Molding Sand

Effect of K+ Diffusion on Hydration of Magnesium Potassium Phosphate Cement with Different Mg/P Ratios: Experiments and Molecular Dynamics Simulation Calculations

Effect of Phosphoric Acid and Soluble Phosphate on the Properties of Magnesium Oxychloride Cement

Effect of Borate Concentration on Solidification of Radioactive Wastes by Different Cements

Effects of magnesia and borax on the compressive strength and microstructure of phosphoric acid-activated metakaolin geopolymer

Effect of zinc oxide on magnesium potassium phosphate cement synthesis

The Influence of the Magnesium-to-Phosphate Molar Ratio on Magnesium Potassium Phosphate Cement Properties Using Either Wollastonite or Volcanic Ash as Fillers

The Effect of Alcohol Compound on the Solidification of Magnesium Oxysulfate Cement-Boron Mud Blends

Effects of Mesoporous Calcium Magnesium Silicate on Setting Time, Compressive Strength, Apatite Formation, Degradability and Cell Behavior to Magnesium Phosphate Based Bone Cements

Effects of fly ash, phosphoric acid, and nano-silica on the properties of magnesium oxychloride cement

Study on the Preparation and Compressive Strength of Boron Mud-Based Basic Magnesium Sulfate Cement

Effect of borax on the hydration and hardening of β-hemihydrate gypsum at high water–plaster ratio

Magnesium–Calcium Phosphate Cements with Sodium Hyaluronate

Study on flexural resistance and hydration mechanism of magnesium phosphate cement