Abstract:Metallic sodium (Na) has been regarded as one of the most attractive anodes for Na-based rechargeable batteries due to its high specific capacity, low working potential, and high natural abundance. However, several important issues hinder the practical application of the metallic Na anode, including its high reactivity with electrolytes, uncontrolled dendrite growth, and poor processability. Metal nitrates are common electrolyte additives used to stabilize the solid electrolyte interphase (SEI) on Na anodes, though they typically suffer from poor solubility in electrolyte solvents. To address these issues, a Na/NaNO3 composite foil electrode was fabricated through a mechanical kneading approach, which featured uniform embedment of NaNO3 in a metallic Na matrix. During the battery cycling, NaNO3 was reduced by metallic Na sustainably, which addressed the issue of low solubility of an SEI stabilizer. Due to the supplemental effect of NaNO3, a stable SEI with NaNxOy and Na3N species was produced, which allowed fast ion transport. As a result, stable electrochemical performance for 600 h was achieved for Na/NaNO3||Na/NaNO3 symmetric cells at a current density of 0.5 mA cm–2 and an areal capacity of 0.5 mAh cm–2. A Na/NaNO3||Na3V2(PO4)2O2F cell with active metallic Na of ∼5 mAh cm–2 at the anode showed stable cycling for 180 cycles. In contrast, a Na||Na3V2(PO4)2O2F cell only displayed less than 80 cycles under the same conditions. Moreover, the processability of the Na/NaNO3 composite foil was also significantly improved due to the introduction of NaNO3, in contrast to the soft and sticky pure metallic Na. Mechanical kneading of soft alkali metals and their corresponding nitrates provides a new strategy for the utilization of anode stabilizers (besides direct addition into electrolytes) to improve their electrochemical performance.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.1c01571?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.1c01571</a>.Additional digital and SEM images; additional XPS results; additional CVs and Nyquist plots; additional Tables for the fitting results of the Nyquist plots; and additional voltage profiles, cycle performance, and voltage curves (<a class="ext-link" href="/doi/suppl/10.1021/acsami.1c01571/suppl_file/am1c01571_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

In-plane isotropic separator-induced highly efficient sodium plating for unlocking the fast-charging capability of anode-free sodium battery at practical conditions

Modification of Polypropylene Separator with Multifunctional Layers to Achieve Highly Stable Sodium Metal Anode

Superior Stable and Long Life Sodium Metal Anodes Achieved by Atomic Layer Deposition.

Refined Electrolyte and Interfacial Chemistry toward Realization of High-Energy Anode-Free Rechargeable Sodium Batteries

Stable Sodium Metal Batteries in Carbonate Electrolytes Achieved by Bifunctional, Sustainable Separators with Tailored Alignment

Addressing the Low Solubility of a Solid Electrolyte Interphase Stabilizer in an Electrolyte by Composite Battery Anode Design

Robust Anode‐Free Sodium Batteries with Durably Sodophilic Interfaces by Suppressing Sodium‐Alloy Transformation

Multifunctional High‐Entropy Alloy Nanolayer Toward Long‐Life Anode‐Free Sodium Metal Battery

A "liquid‐in‐solid" Electrolyte for High‐Voltage Anode‐Free Rechargeable Sodium Batteries

Amorphous phosphatized hybrid interfacial layer for dendrite-free sodium deposition

Multifunctionalized Safe Separator Toward Practical Sodium‐Metal Batteries with High‐Performance under High Mass Loading

Electrolyte Solvation Engineering Stabilizing Anode‐Free Sodium Metal Battery With 4.0 V‐Class Layered Oxide Cathode

Ferroelectric interface for efficient sodium metal cycling in anode-free solid-state batteries

An autotransferable alloy overlayer toward stable sodium metal anodes

Nucleophilic Sn Seeding and Interface Engineering for Highly Stable Sodium Metal Batteries

Rapid and reversible Na deposition onto Al nanosheet arrays

An in-situ formed stable interface layer for high-performance sodium metal anode in a non-flammable electrolyte

Stable sodium metal anode enabled by interfacial room‐temperature liquid metal engineering for high‐performance sodium–sulfur batteries with carbonate‐based electrolyte

Smoothing The Sodium-Metal Anode With A Self-Regulating Alloy Interface For High-Energy And Sustainable Sodium-Metal Batteries

Optimizing Na plating/stripping by a liquid sodiophilic Ga-Sn-In alloy towards dendrite-poor sodium metal anodes

Dendrite‐free Lithium and Sodium Metal Anodes with Deep Plating/stripping Properties for Lithium and Sodium Batteries