Abstract:Metallic sodium (Na) has been regarded as one of the most attractive anodes for Na-based rechargeable batteries due to its high specific capacity, low working potential, and high natural abundance. However, several important issues hinder the practical application of the metallic Na anode, including its high reactivity with electrolytes, uncontrolled dendrite growth, and poor processability. Metal nitrates are common electrolyte additives used to stabilize the solid electrolyte interphase (SEI) on Na anodes, though they typically suffer from poor solubility in electrolyte solvents. To address these issues, a Na/NaNO3 composite foil electrode was fabricated through a mechanical kneading approach, which featured uniform embedment of NaNO3 in a metallic Na matrix. During the battery cycling, NaNO3 was reduced by metallic Na sustainably, which addressed the issue of low solubility of an SEI stabilizer. Due to the supplemental effect of NaNO3, a stable SEI with NaNxOy and Na3N species was produced, which allowed fast ion transport. As a result, stable electrochemical performance for 600 h was achieved for Na/NaNO3||Na/NaNO3 symmetric cells at a current density of 0.5 mA cm–2 and an areal capacity of 0.5 mAh cm–2. A Na/NaNO3||Na3V2(PO4)2O2F cell with active metallic Na of ∼5 mAh cm–2 at the anode showed stable cycling for 180 cycles. In contrast, a Na||Na3V2(PO4)2O2F cell only displayed less than 80 cycles under the same conditions. Moreover, the processability of the Na/NaNO3 composite foil was also significantly improved due to the introduction of NaNO3, in contrast to the soft and sticky pure metallic Na. Mechanical kneading of soft alkali metals and their corresponding nitrates provides a new strategy for the utilization of anode stabilizers (besides direct addition into electrolytes) to improve their electrochemical performance.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.1c01571?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.1c01571</a>.Additional digital and SEM images; additional XPS results; additional CVs and Nyquist plots; additional Tables for the fitting results of the Nyquist plots; and additional voltage profiles, cycle performance, and voltage curves (<a class="ext-link" href="/doi/suppl/10.1021/acsami.1c01571/suppl_file/am1c01571_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Addressing the Low Solubility of a Solid Electrolyte Interphase Stabilizer in an Electrolyte by Composite Battery Anode Design

A robust, highly reversible, mixed conducting sodium metal anode

Stable Na Metal Anode Enabled by a Reinforced Multistructural SEI Layer

Homogeneous Metallic Deposition Regulated by Porous Framework and Selenization Interphase Toward Stable Sodium/Potassium Anodes

Rational Design of an Artificial SEI: Alloy/Solid Electrolyte Hybrid Layer for a Highly Reversible Na and K Metal Anode

Stable Sodium Metal Anode Enabled by an Interface Protection Layer Rich in Organic Sulfide Salt

Stabilizing Electrode-Electrolyte Interface Via Crown Ether-Containing Selective Coating for Dendrite-Free Na-K Anode-Based Solid-State Sodium Batteries

Sodiophilic Decoration of a Three-Dimensional Conductive Scaffold toward a Stable Na Metal Anode

Designing Solid Electrolyte Interfaces towards Homogeneous Na Deposition: Theoretical Guidelines for Electrolyte Additives and Superior High-Rate Cycling Stability

A Salt‐in‐Metal Anode: Stabilizing the Solid Electrolyte Interphase to Enable Prolonged Battery Cycling

Enabling High-Performance Sodium Metal Anodes Via A Sodiophilic Structure Constructed by Hierarchical Sb2MoO6 Microspheres

Highly Stable Sodium Metal Batteries Enabled by Manipulating the Fluorinated Organic Components of Solid‐Electrolyte‐Interphase

An in-situ formed stable interface layer for high-performance sodium metal anode in a non-flammable electrolyte

Na (100)‐Textured Electrode Embedded with Sb‐Doped SnO2 Nanoparticles for Dendrite‐Free Sodium Metal Batteries

Realizing a Highly Stable Sodium Battery with Dendrite-Free Sodium Metal Composite Anodes and O3-type Cathodes

Self-forming Na3P/Na2O Interphase on a Novel Biphasic Na3Zr2Si2PO12/Na3PO4 Solid Electrolyte for Long-Cycling Solid-State Na-metal Batteries

Recent Development of Na Metal Anodes: Interphase Engineering Chemistries Determine the Electrochemical Performance

3D Printed Sodiophilic Nb2CTx/Reduced Graphene Oxide Monoliths Enable Long Cycle Stability of Sodium Metal Anodes

Stabilizing sodium metal anode by in-situ formed Ag metal layer

Embedding a Percolated Dual-Conductive Skeleton with High Sodiophilicity Toward Stable Sodium Metal Anodes

Salt Engineering Toward Stable Cation Migration of Na Metal Anodes