Abstract:Magnesium and its alloys are promising candidate materials for medical implants because they possess excellent biocompatibility and mechanical properties comparable to bone. Furthermore, secondary surgical operations for removal could be eliminated due to magnesium's biodegradability. However, magnesium's degradation rate in aqueous environments is too high for most applications. It has been reported that hydrophobic textured surfaces can trap a surface gas layer which acts as a protective barrier against corrosion. However, prior studies have not investigated separately the role of the texture and hydrophobic treatments on magnesium corrosion rates. In this study, pillar-shaped microstructure patterns were fabricated on polished high purity magnesium surfaces by ablation with a picosecond laser. Some micropatterned samples were further processed by stearic acid modification (SAM). Micropatterned surfaces with SAM had hydrophobic properties with water droplet contact angles greater than 130°, while the micropatterned surfaces without SAM remained hydrophilic. The corrosion properties of textured and smooth magnesium surfaces in saline solution were investigated using electrochemical impedance spectroscopy (EIS) and optical microscopy. Corrosion rates on both hydrophobic and hydrophilic laser machined surfaces were reduced ∼90% relative to polished surfaces. Surprisingly, corrosion rates were similar for both hydrophobic and hydrophilic surfaces. Indirect evidence of local alkalization near microstructures was found and was hypothesized to stabilize the Mg(OH)2 layer, thereby inhibiting corrosion on hydrophilic surfaces. This is different than the corrosion resistance mechanism for superhydrophobic surfaces which makes use of gas adhesion at the liquid solid interface. These results suggest additional processing to render the magnesium hydrophobic is not necessary since it does not significantly enhance the corrosion resistance beyond what is conferred by micropatterned textures.

Improved corrosion behavior of high-purity Mg surface modified by laser scanning and polycaprolactone spin coating

Polycaprolactone/ZnO Coating on WE43 Magnesium Alloy Combined with a MgO/MgCO3 Transition Layer for Promoting Anticorrosion and Interfacial Adhesion

Study on Hydrophobic Surface of Magnesium Alloy Prepared by Femtosecond Laser and its Corrosion Resistance

Fabrication of Electroactive Poly(γ‐glutamic Acid) Coating for Improving Corrosion Resistance and Cytocompatibility of Magnesium Alloy

Microstructures and Properties in Surface Layers of Mg-6Zn-1Ca Magnesium Alloy Laser-Clad with Al-Si Powders

A Combined Coating Strategy Based on Atomic Layer Deposition for Enhancement of Corrosion Resistance of AZ31 Magnesium Alloy

Laser Cladding of a Mg Based Mg–Gd–Y–Zr Alloy with Al–Si Powders

A Superior Corrosion Protection of Mg Alloy via Smart Nontoxic Hybrid Inhibitor-Containing Coatings

Surface modification of biomedical Mg-Ca and Mg-Zn-Ca alloys using selective laser melting: Corrosion behaviour, microhardness and biocompatibility

Progress of laser surface treatment on magnesium alloy

Improve the binding force of PEEK coating with Mg surface by femtosecond lasers induced micro/nanostructures

Preparation of poly(ε‐caprolactone)‐hydroxyapatite composite coating for improvement of corrosion performance of biodegradable magnesium

Deposition and corrosion performance of phosphate-polylactic acid composite coatings on WE43 magnesium alloy

Laser machined micropatterns as corrosion protection of both hydrophobic and hydrophilic magnesium

Biocorrosion resistance and biocompatibility of Mg–Al layered double hydroxide/poly-L-glutamic acid hybrid coating on magnesium alloy AZ31

Biodegradable Poly(L-lactic acid) (PLLA) Coatings Fabricated from Non-Solvent Induced Phase Separation for Improving Corrosion Resistance of Magnesium Rods in Biological Fluids.

Laser processing of Mg-10Li-3Al-3Zn alloy:Part II- Improving corrosion resistance of multi-phase Mg alloys by laser surface processing

A Simple Surface Treatment for Mg to Gain Enhanced Resistance to Corrosion and Corrosive Wear by Hammering Al Powder‐Covered Mg Substrate

Photo-Cross-Linked Polycarbonate Coating with Surface-Erosion Behavior for Corrosion Resistance and Cytocompatibility Enhancement of Magnesium Alloy

Pure magnesium laser surface modification using Nd:YAG laser

One-Pot but Two-Step Vapor-Based Amine- and Fluorine-Bearing Dual-Layer Coating for Improving Anticorrosion and Biocompatibility of Magnesium Alloy