Abstract:Introduction. Structural materials, including materials made of heat-resistant and hard-to-work steels, are widely used in various branches of mechanical engineering. To increase the efficiency of manufacturing parts of thermal equipment from heat-resistant and hard-to-work steels, the technological method of cutting with preliminary plasma heating of the workpiece is used. There is also a technological method of cutting metals, including hard-to-process materials by ultrasonic turning. Proceeding from this, in order to increase the efficiency of plasma machining of hard-to-process materials, it is necessary to investigate the technological possibilities of using ultrasonic turning of hard-to-process materials during plasma machining. The purpose of the work: to investigate the wear of cutting tools when using ultrasound in the conditions of plasma-mechanical processing of parts made of hard-to-process materials. The paper investigates the features of the plasma-mechanical processing under ultrasonic cutting conditions and determines the wear values of carbide cutters VK8, T5K10 and T15K6 when processing steels of grades 20Cr13Ni18 and 20Cr25Ni20Si2(cast). And also the wear of these cutters was determined under the conditions of conventional turning of the same materials to compare the results of wear of the cutters in different processing conditions. The research method is to determine the linear wear of carbide cutters along the back surface with conventional, plasma-mechanical and plasma-mechanical cutting assisted with ultrasonic cutting using an instrumental microscope and visual estimation with a 10x magnifying glass. Results and discussion. The paper presents the results of experimental studies to determine the wear of cutting tools when processing heat-resistant steels of the 20Cr13Ni18 and 20Cr25Ni20Si2(cast) grades with carbide cutters of the VK8, T5K10 and T15K6 grades. Studies were carried out to determine the wear of carbide cutters as with conventional mechanical cutting, plasma-mechanical cutting, as well as plasma-mechanical cutting using ultrasound. The experiments were carried out when turning these materials on a modernized lathe mod.1A64. A rectifier with a controlled choke and a plasma torch mod.APR-403 are connected to the lathe; a plasma holder is placed on the lathe carriage. A semiconductor rectifier serves as a power source with a compressed electric arc of current. The arcing takes place between the cathode (plasma torch) and the anode (blank) at the point of the plasma-forming gas; compressed air passes through the nozzle channel of the plasma torch. During the experiments, the position of the plasma torch was adjusted relative to the part rotation axis. When conducting experiments on studying the wear of cutters under conditions of ultrasonic plasma-mechanical cutting, ultrasound was applied to the cutting edge using a device developed by the authors. When processing heat-resistant steels under the usual turning condition, processing modes were adopted: cutting speed V = 10 m/min, cutting depth t = 3...4 mm, longitudinal feed Sl = 0.31 mm/rev. It is found that when processing steel grade 20Cr13Ni18 by conventional cutting, the back surface of the carbide cutter made of T5K10 wears out to 1 mm in size within 10 minutes, and for the cutter made of VK8 – within 15 minutes. During plasma machining, the cutting speed and the feed rate were increased 2 times; the results of the wear of the cutters show that at the same time T5K10 wears out to 1 mm within 20 minutes, VK8 – within 25 minutes. Plasma-mechanical processing using ultrasound show that the carbide cutter T5K10 wears out by 0.50 mm in less than 50 minutes of cutting, and VK8 wears out by 0.35 mm. The same results are obtained when processing heat-resistant steel 20Cr25Ni20Si2(cast). Thus, the study of wear of carbide cutters in the processing of heat-resistant steels shows that the use of ultrasonic cutting in plasma-mechanical processing of steels can significantly reduce the amount of tool wear. The presented results confirm the prospects of using ultrasonic plasma-mechanical cutting of heat-resistant steels with blade tools.

Comparison of laser beam, oxygen and plasma arc cutting methods in terms of their advantages and disadvantages in cutting structural steels

A comprehensive review of studying the influence of laser cutting parameters on surface and kerf quality of metals

A comparative study of the thermal and mechanical cutting influence on the cut-edge hardness of structural steels S355 and S1100

Experimental Investigation of Industrial Laser Cutting: The Effect of the Material Selection and the Process Parameters on the Kerf Quality

Influence of high-energy impact during plasma cutting on structure and properties of surface layers of aluminum and titanium alloys

Research on Mechanized Plasma Gouging of Weldable Construction Steels

Experimental Comparison of the Microstructure and Surface Roughness in CO2 Laser Cutting of the Titanium Alloy Ti–6Al–4V and the Pure Titanium Ti

The Advancement of Waterjet-Guided Laser Cutting System for Enhanced Surface Quality in AISI 1020 Steel Sheets

Effects of Cutting Geometries and Cutting Parameters on the Surface Roughness and Kerf Width of X60 Steel Machined by Laser Beam

Laser Cutting of Titanium Alloy Plates: A Review of Processing, Microstructure, and Mechanical Properties

Effect of Fiber-Laser Parameters on Cutting Accuracy of Thin and Thick S355JR Structural Steel Plates

Laser cutting of ductile cast iron

Development of Equipment and Technology for Precision Air-Plasma Cutting of Plate Steel

Analysis based on surface and kerf performance in multi-simultaneous cutting of S235JR structural steel with abrasive water jet

Comparison of the features of the formation of joints of aluminum alloy 7075 (Al-Zn-Mg-Cu) by laser, microplasma, and laser-microplasma welding

Comparative Study Regarding the Welding Behavior of Galvanized Steel Using Laser Welding and Gas Metal Arc Welding Processes

A Review: Laser Welding of Dissimilar Materials (Al/Fe, Al/Ti, Al/Cu)—Methods and Techniques, Microstructure and Properties

Fusion cutting of aluminum, magnesium, and titanium alloys using high-power fiber laser

Features of ultrasound application in plasma-mechanical processing of parts made of hard-to-process materials

Comparison between Abrasive Water Jet Cutting and Laser Cutting

Surface Structure Formation in Plasma Cutting of Aluminum and Titanium Alloys Using Direct Current Straight and Reverse Polarity