Abstract:This study covered the design, implementation and performance evaluation of a crossflow turbine at various nozzle positions. The chosen blade material was analyzed using ANSYS for stress and deformation degree under the impact of hydraulic jets to ascertain its suitability while in operation. The shaft was analyzed under static and dynamic conditions using ANSYS in order to ensure a non-plastic deformation of the shaft at both conditions. The outcome of this analysis was employed in the harmonic response analysis of the runner shaft. Convergent tests were done for both the blade and runner shaft analysis. An experiment was designed for the evaluation of the crossflow turbine performance using optimal (custom) design tool of response surface methodology and 69 simulations/runs were obtained. The factors considered in the experimental design are: nozzle distance from the shaft, nozzle height and attack angle. The crossflow turbine was constructed using computed design values for all the machine's parts. The runner blades were positioned specifically at 28° outer blade angle and 90° inner blade angle. The turbine was tested under a water head and flow rate of 6.4m and 0.0042 m 3 / s respectively. The shaft power and efficiency were evaluated using their respective formula. The responses were optimized in order to get the optimum position of the nozzle that would give the best performance of the responses using the two factor interaction (2F1) mathematical models in coded factors, developed for each of the response. The results obtained, proved that low carbon steel material was suitable for the turbine blading and the shaft is safe at both static and dynamic conditions since the induced stresses and deformations never exceeded the permissible range. Also, each of these considered nozzle positions had a significant effect on the responses with the nozzle height and attack angle having a combined effect on the performance of the turbine. The best turbine performance was obtained at lower angle of attack, nozzle distance very close to the runner shaft and at a nozzle height that will actualize greater energy impartation to the upper and lower blade profiles. The developed mathematical models for each response has higher correlation value, suggesting that the models are suitable for predicting the responses at the considered factor levels. An optimal nozzle distance, height and attack angle of 102mm, 413mm and 5 ° respectively, were obtained. At this nozzle position, the alternator gave an output of 35watts and 6V. When two voltage transformers were employed, it gave 200Volts AC. The turbine can be commercialized on large scale for greater output power using the determined optimal nozzle positions.

Study on the Flow Field of an Undershot Cross-Flow Water Turbine

Research on the flow field of undershot cross-flow water turbines using experiments and numerical analysis

Study on the Effects of Runner Geometries on the Performance of Inline Cross-Flow Turbine Used in Water Pipelines

Numerical Study on the Impact of Runner Inlet Arc Angle on the Performance of Inline Cross-Flow Turbine Used in Urban Water Mains

Development of an Inline Vertical Cross-Flow Turbine for Hydropower Harvesting in Urban Water Supply Pipes

Study on the Effects of Blades Outer Angle on the Performance of Inline Cross-Flow Turbines

Effects of Different Block Designs on the Performance of Inline Cross-Flow Turbines in Urban Water Mains

Performance and Flow Field of a Gravitation Vortex Type Water Turbine

Performance Enhancement of an Inline Cross-FLow Hydro Turbine for Power Supply to Water Leakage Monitoring System

Development of an Inline Bidirectional Micro Crossflow Turbine for Hydropower Harvesting from Water Supply Pipelines

Investigation into the Flow Details of Runner Region in A Pump Turbine at Off-Design Conditions

Analysis of Flow Field Characteristics and Pressure Pulsation in Horizontal Axis Double-Runner Francis Turbine

Numerical analysis and performance enhancement of a cross-flow hydro turbine

Design and implementation of a crossflow turbine for Pico hydropower electricity generation

Numerical simulation of free-surface flow in updraft-free-exit-flow hydropower turbine

Changes in power generation performance of an undershot cross-flow-type hydraulic turbine in an irrigation channel due to snow masses passing through the rotor

Experimental research and turbulent flow simulation of the updraft free-exit-flow hydropower turbine system

A Study and Optimization of the Unsteady Flow Characteristics in the Last Stage Impeller of a Small-Scale Multi-Stage Hydraulic Turbine

Experimental and numerical investigation of vortex flows and pressure fluctuations in a high-head pump-turbine

Numerical Investigation of Inner Flow Characteristics of a Prototype Pump Turbine with a Single Pier in Draft Tube at Part Load Conditions

Study on Pressure Pulsation and Force Characteristics of Kaplan Turbine