Defects Give New Life to an Old Material: Electronically Leaky Titania as a Photoanode Protection Layer

Kevin Sivula

DOI: https://doi.org/10.1002/cctc.201402532

IF: 4.5

2014-08-27

ChemCatChem

Abstract:Watch that leak! Amorphous titania overlayers together with an intermixing of nickel catalyst can facilitate hole transport and give stability to traditional semiconductors for use as photoanodes for solar water oxidation.

chemistry, physical

What problem does this paper attempt to address?

Titanium oxide crystallization and interface defect passivation for high performance insulator-protected Schottky junction MIS photoanodes.

Andrew G Scheuermann,John P Lawrence,Andrew C Meng,Kechao Tang,Olivia L Hendricks,Christopher E D Chidsey,Paul C McIntyre

DOI: https://doi.org/10.1021/acsami.6b03688

IF: 9.5

2016-01-01

ACS Applied Materials & Interfaces

Abstract:Atomic layer deposited (ALD) TiO2 protection layers may allow for the development of both highly efficient and stable photoanodes for solar fuel synthesis; however, the very different conductivities and photovoltages reported for TiO2-protected silicon anodes prepared using similar ALD conditions indicate that mechanisms that set these key properties are, as yet, poorly understood. In this report, we study hydrogen-containing annealing treatments and find that post-catalyst-deposition anneals at intermediate temperatures reproducibly yield decreased oxide/silicon interface trap densities and high photovoltage. A previously-reported insulator thickness-dependent photovoltage loss in metal-insulator-semiconductor Schottky junction photoanodes is suppressed, and this occurs simultaneously with TiO2 crystallization and an increase in its dielectric constant. At small insulator thickness, a record for a Schottky junction photoanode of 623 mV photovoltage is achieved, yielding a photocurrent turn-on at 0.92 V vs NHE or -0.303 V with respect to the thermodynamic potential for water oxidation.
Hole-Selective Hybrid TiO2 Layer towards Long-Term Stability of Low-Cost Photoanodes in Solar Water Oxidation

David Tilley,Sanghyun Bae,Thomas Moehl,Erin Service,Minjung Kim,Pardis Adams,Zhenbin Wang,Yuri Choi,Jungki Ryu

DOI: https://doi.org/10.26434/chemrxiv-2024-n216n

2024-03-04

Abstract:The use of conductive and corrosion-resistant protective layers represents a key strategy for improving the durability of light absorber materials in photoelectrochemical water splitting. For high performance photoanodes such as Si, GaAs, and GaP, amorphous TiO2 (a-TiO2) protective overlayers, deposited by atomic layer deposition, are conductive for holes via a defect band in the TiO2. However, when coated on simply prepared, low-cost photoanodes such as metal oxides, no charge transfer is observed through a-TiO2. Here, we report a hybrid polyethyleneimine (PEI)/TiO2 layer that facilitates hole transfer from model oxides BiVO4 and Fe2O3, enabling access to a broader scope of available materials for practical water oxidation. A thin PEI layer between the light absorber and the hybrid PEI/TiO2 acts as a hole-selective interface, improving the optoelectronic properties of the photoanode devices. These PEI/TiO2 modified photoanodes exhibit high photostability for solar water oxidation (~2 mA cm-2 for > 120 h).

Chemistry
Defect-Tolerant TiO 2 -Coated and Discretized Photoanodes for >600 h of Stable Photoelectrochemical Water Oxidation

Xin Shen,Maoqing Yao,Ke Sun,Tianshuo Zhao,Yulian He,Chun-Yung Chi,Chongwu Zhou,Paul Daniel Dapkus,Nathan S. Lewis,Shu Hu

DOI: https://doi.org/10.1021/acsenergylett.0c02521

IF: 22

2020-12-16

ACS Energy Letters

Abstract:Arrays of GaAs nanowires have been grown by selective-area metal–organic chemical-vapor deposition (MOCVD) onto photoactive planar Si substrates. This tandem, vertical-wire-array-on-planar absorber was then coated by atomic layer deposition (ALD) of an amorphous TiO2 (a-TiO2) stabilization layer, followed by deposition of a NiOx electrocatalyst layer. The tandem planar Si/nanowire GaAs/a-TiO2/NiOx photoanodes exhibited continuous solar-driven water oxidation in 1.0 M KOH(aq) for over 600 h without substantial photocurrent decay. The preservation of the nanowire morphology and structural integrity during >600 h of photoanodic operation confirms the benefits of mitigating and isolating nanoscale defects via the architecture of discretized absorbers on a self-passivating and insulating substrate. Nanoscale morphology and compositions of the photoanode after 600 h of testing were characterized to reveal the self-limiting corrosion behavior. It provides a promising approach to develop efficient but otherwise unstable absorbers such as III–V materials into defect-tolerant, corrosion-resistant photoanodes.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsenergylett.0c02521?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsenergylett.0c02521</a>.Experimental details about the fabrication process, performance, and stability tests, simulation for the p+-Si/n+-GaAs junction, schematics for the electrode structure, cell setup, and band diagram, SEM, EDS, and TEM for morphological and structural characterizations, additional performance data, repeated stability test results, and detailed corrosion behavior discussions (<a class="ext-link" href="/doi/suppl/10.1021/acsenergylett.0c02521/suppl_file/nz0c02521_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology,energy & fuels,electrochemistry
Interplay between Collective and Localized Effects of Point Defects on Photoelectrochemical Performance of TiO2 Photoanodes for Oxygen Evolution

Mengya Yang,Junyi Cui,Matyas Daboczi,Robert V. Law,Joel Luke,Ji‐Seon Kim,Anna Hankin,Salvador Eslava

DOI: https://doi.org/10.1002/admi.202300595

IF: 5.4

2023-09-21

Advanced Materials Interfaces

Abstract:The study presents a successful modification of anatase TiO2 photoanodes with point defects such as oxygen and titanium vacancies to have both collective and localized effects that boost their photoelectrochemical performance. The improved performance is due to enhanced light absorption, conductivity, and photovoltage, as well as a more negative flat‐band potential and increase in hole flux to the semiconductor–electrolyte interface. Among the various photoanode materials investigated for photoelectrochemical water splitting cells, TiO2 stands out due to its abundance, stability, and favorable valence band edge for water oxidation. In this study, the importance of introducing and combining oxygen and titanium vacancy point defects in anatase TiO2 photoanodes to improve their performance is unveiled, achieving a photocurrent density of 0.73 (±0.015) mA cm−2 at +1.23 VRHE under 100 mW cm−2 of simulated sunlight or 26.4 mA cm−2 at +1.23 VRHE under 100 mW cm−2 of 365 nm light. The characterization by X‐ray photoelectron spectroscopy, surface photovoltage, and electron paramagnetic resonance demonstrates that these oxygen and titanium vacancies can have both collective and localized positive effects on the material, leading to a narrowing of the bandgap, an increase in donor density, and an increase in hydroxyl groups on the surface of TiO2. These result in enhanced light absorption, conductivity, and photovoltage, as well as a more negative flat‐band potential and increase in hole flux to the semiconductor–electrolyte interface. These findings provide valuable insights into the role of point defects in modulating the properties of TiO2 and have important implications for the development of high‐performance TiO2‐based devices.

materials science, multidisciplinary,chemistry
PPy‐encapsulated SnS2 Nanosheets Stabilized by Defects on a TiO2 Support As a Durable Anode Material for Lithium‐Ion Batteries

Ling Wu,Jie Zheng,Liang Wang,Xunhui Xiong,Yanyan Shao,Gang Wang,Jeng-Han Wang,Shengkui Zhong,Minghong Wu

DOI: https://doi.org/10.1002/anie.201811784

2019-01-01

Abstract:Nanostructured-alloy-type anodes have received great interest for high-performance lithium-ion batteries (LIBs). However, these anodes experience huge volume fluctuations during repeated lithiation/delithiation and are easily pulverized and subsequently form aggregates. Herein, an efficient method to stabilize alloy-type anodes by creating defects on the surface of the metal oxide support is proposed. As a demonstration, PPy-encapsulated SnS2 nanosheets supported on defect-rich TiO2 nanotubes were produced and investigated as an anode material for LIBs. Both experimental results and theoretical calculations demonstrate that defect-rich TiO2 provides more chemical adhesions to SnS2 and discharge products, compared to defect-poor TiO2, and then effectively stabilizes the electrode structure. As a result, the composite exhibits an unprecedented cycle stability. This work paves the way to designing durable and active nanostructured-alloy-type anodes on oxide supports.
Defect Engineering for Photocatalysis: From Ternary to Perovskite Oxynitrides

Joshua J. Brown,Zhuofeng Ke,Tianyi Ma,Alister J. Page

DOI: https://doi.org/10.1002/cnma.201900703

IF: 3.82

2020-02-06

ChemNanoMat

Abstract:Exploiting defects and specific anion non‐stoichiometry in mixed‐anion semiconductors is a challenge that remains at the forefront of photocatalytic and photoelectrochemical water splitting research. The interplay between of oxygen and nitrogen defects in perovskite oxynitrides specifically creates exciting, yet complex, opportunities for optimizing phase stability, ionic conduction and anion order in these materials. In this Minireview we highlight the recent advances in defect engineering in oxynitride semiconductors, such as anion content/non‐stoichiometry, surface modification, cation doping and formation of anisotropic layered structures, on photocatalytic and photoelectrochemical water splitting. Avenues warranting further investigation are discussed.

materials science, multidisciplinary,nanoscience & nanotechnology,chemistry
Sputter-Coated TiO 2 Films as Passivation and Hole Transfer Layers for Improved Energy Conversion with Solar Fuel WO 3 /CuWO 4 Photoanodes

Lucas Caniati Escaliante,Nilton Francelosi Azevedo Neto,Hervin Errol Mendoza,Chengcan Xiao,Rajesh Kandel,Jose Humberto Dias da Silva,Frank E. Osterloh

DOI: https://doi.org/10.1021/acsami.4c14214

IF: 9.5

2024-12-04

ACS Applied Materials & Interfaces

Abstract:Atomic-layer-deposited (ALD) "leaky" TiO(2) has gained interest as a charge-selective protection layer for semiconductor solar fuel electrodes. Here, the use of sputter-deposited TiO(2) layers as hole-selective contacts for WO(3)/CuWO(4) type-2 heterojunction water oxidation photoanodes is demonstrated for the first time. TiO(2) protection layers with varying thicknesses (2 to 128 nm) were deposited by using the radio frequency (RF) magnetron sputtering technique. The resulting TiO(2) films are...

materials science, multidisciplinary,nanoscience & nanotechnology
Highly Enhanced Photoelectrocatalytic Properties by Α-Fe 2 O 3 Modified NF-TiO 2 Pyramids with Dominant (101) Facets

Qi Wang,Naxin Zhu,Enqin Liu,Leiling Fu,Tiantian Zhou,Yanqing Cong

DOI: https://doi.org/10.1016/j.electacta.2016.09.025

IF: 6.6

2016-01-01

Electrochimica Acta

Abstract:Visible-light-active Fe2O3/NF-TiO2 film was prepared by depositing alpha-Fe2O3 nanoparticles onto the surface of pyramid-shaped NF-TiO2 via sequential electro-deposition and electro-anodization processes. NF-TiO2 with dominant (101) facets was obtained via calcining TiO2 nanotubes (TiO2-NTs) in the presence of NH4F. The structural and optical properties were carefully studied by XRD, SEM, HRTEM, XPS and UV-Vis-DRS. Photoelectrochemical measurements, such as linear sweep voltammetry (LSV), electrochemical impedance spectroscopy (EIS) and Mott-Schottky (M-S) plots, were also carried out to investigate the generation, separation and transfer of photogenerated charges. It was found that Fe2O3/NF-TiO2 exhibited the best photoelectrocatalytic (PEC) activity relative to Fe2O3/TiO2-NTs or Fe2O3/N-TiO2. The formation of anatase-rutile heterojunction, wider spectral response, increased photocurrent response and greatly reduced charge transfer resistance, could be positive driving force for the enhanced PEC activity. Simultaneous PEC reduction of Cr(VI) and degradation of phenol were evaluated under visible light using Fe2O3/NF-TiO2 film as photoanode and Ti sheet as cathode. The calculated rate constants for Cr(VI) and phenol were 4.3 and 3.6 times relative to that on Fe2O3/TiO2-NTs, respectively. Good stability was also confirmed in cyclic runs using the optimized photoanode. (C) 2016 Elsevier Ltd. All rights reserved.
A Dual-Layer Titania Film with Enhanced Photocatalytic Activity

Xiao-Mei Song,Jin-Ming Wu,Gao-Jie Zhang,Mi Yan

DOI: https://doi.org/10.1021/jp902049q

2009-01-01

Abstract:A dual-layer titania film consisting of a sol-gel anatase layer over an interconnected porous anatase one was fabricated and its photoelectrochemical behavior as well as photocatalytic ability were studied in detail. The porous layer was fabricated through direct oxidation of a metallic Ti substrate with an aqueous hydrogen peroxide at 80 degrees C for 1 h. The Ti substrate with the porous titania layer was then subjected to a sol-gel spin-coating to deposit the upper titania layer. The dual-layer titania film as a whole was phase pure anatase after a subsequent thermal treatment at 450 degrees C. The UV-vis diffuse reflectance spectra and ambient photoluminescence spectra indicated that the porous anatase possessed a band gap width narrower than that of the sol-gel derived anatase, which was attributed to the relatively larger amounts of surface oxygen deficiency. Under UV illumination, both the saturated photocurrent and the activity to assist photodegradation of rhodamine B in water were nearly double that of the simply summation of those exhibited by the two component layers alone for the dual-layer film. The photocatalytic activity of the dual-layer film was even 3.5 times that of the sol-gel derived anatase film with identical film weight. This work demonstrates that an appropriate configuration of two titania layers derived by distinct routes, even if the titania is of the same crystal structure such as anatase, is possible to improve significantly the photoelectrochemical response as well as the photocatalytic activity, providing that the band gap of each titania is aligned properly so that the charge separation efficiency can be enhanced significantly.
Electronic defects in metal oxide photocatalysts

Ernest Pastor,Michael Sachs,Shababa Selim,James R. Durrant,Artem A. Bakulin,Aron Walsh

DOI: https://doi.org/10.1038/s41578-022-00433-0

IF: 83.5

2022-05-05

Nature Reviews Materials

Abstract:Nature Reviews Materials, Published online: 04 May 2022; doi:10.1038/s41578-022-00433-0 Defects have a key role in determining the functionality of solids and can make them powerful catalysts. This Review examines defect chemistry in metal oxides and discusses the role that charged defects and polarons have in enabling photoelectrochemical reactions.

materials science, multidisciplinary,nanoscience & nanotechnology
An ultrathin amorphous defective co-doped hematite passivation layer derived via an in situ electrochemical method for durable photoelectrochemical water oxidation

Milad Fathabadi,Mohammad Qorbani,Amr Sabbah,Shaham Quadir,Chih-Yang Huang,Kuei-Hsien Chen,Li-Chyong Chen,Naimeh Naseri

DOI: https://doi.org/10.1039/d2ta03792k

IF: 11.9

2022-08-02

Journal of Materials Chemistry A

Abstract:Although hematite ( i.e. , α-Fe 2 O 3 ) has been widely investigated in photoelectrochemical water oxidation studies due to its high theoretical photocurrent density, it still suffers from serious surface charge recombination and low photoelectrochemical stability. Here we report an in situ electrochemical method to form a uniform and ultrathin ( i.e. , 3–5 nm) passivation layer all over the pores of an optimized ∼3.2% Ti-doped α-Fe 2 O 3 photoanode. We unveil the amorphous and defective nature of the in situ derived layer assigned to a high concentration of oxygen vacancies and intercalated potassium atoms there, i.e. , the formation of Ti/K co-doped defective α-Fe 2 O 3− x . Owing to the efficient passivation of surface states, alleviated surface-potential fluctuations, and low charge-transfer resistance at the interface, photoanodes show an average of ∼60% enhancement in the photoelectrochemical performance, applied bias absorbed photon-to-current efficiency of 0.43%, and faradaic efficiency of ∼88%. Moreover, the passivation layer prevents direct contact between the electrode material and electrolyte, resulting in less degradation and outstanding photoelectrochemical stability with a photocurrent retention of ∼95% after ∼100 hours, albeit by performing several successive in situ electrochemical passivation processes. This work presents an industrially scalable method to controllably engineer the interfaces of semiconductors–electrolytes with precious metal-free defective hematite-based co-catalysts for sustainable photoelectrochemical solar-to-fuel conversion applications.

materials science, multidisciplinary,chemistry, physical,energy & fuels
Operandoelectrochemical Study of Charge Carrier Processes in Water Splitting Photoanodes Protected by Atomic Layer Deposited TiO2

Sebastian Siol

DOI: https://doi.org/10.1039/c9se00399a

IF: 6.813

2019-01-01

Sustainable Energy & Fuels

Abstract:Photoelectrochemical impedance spectroscopy and the dual-working-electrode technique enable the in-depth investigation on the charge carrier processes in ALD-TiO2protected photoanodes.
TiO 2 /TiN Interface Enables Integration of Ni 5 P 4 Electrocatalyst with a III–V Tandem Photoabsorber for Stable Unassisted Solar-Driven Water Splitting

Shinjae Hwang,Hengfei Gu,James L. Young,Myles A. Steiner,Anders B. Laursen,Ryan A. Crichton,Yao-Wen Yeh,Philip E. Batson,Leonard C. Feldman,Mengjun Li,Keenan Wyatt,Ahmad Safari,Todd G. Deutsch,Eric Garfunkel,G. Charles Dismukes

DOI: https://doi.org/10.1021/acsenergylett.3c02606

IF: 22

2024-02-02

ACS Energy Letters

Abstract:H2 production by direct photoelectrochemical (PEC) water splitting has remained unachievable commercially, mainly due to rapid failure at the interface between the photoabsorber(s) and catalyst(s). PEC devices made from multijunction III–V semiconductors with platinum group metal (PGM) catalysts have yielded impressive initial solar-to-H2 (STH) efficiency >19%, which rapidly corrodes in aqueous electrolytes. Here, TiO2/TiN layers were fused to create a bifunctional interface between a GaInP2/GaAs III–V tandem photoabsorber and a polycrystalline Ni5P4 HER catalyst. The TiO2 serves as a conducting corrosion barrier, while a thin layer of much denser TiN (1 nm) blocks interlayer diffusion during fabrication. This strategy allows the elevated temperatures needed to crystallize the Ni5P4 nanoparticles and fuse to the TiO2/TiN junction to achieve minimal optical loss without damaging the sensitive photoasbsorber. The resulting photocathode exhibits an initial STH efficiency of 11.4%–13.2% in sodium phosphate electrolyte at neutral pH 7. It operated continuously for over 200 h without failure above 10% STH efficiency, exceeding all previous benchmarks. The earth-abundant Ni5P4 catalyst replaces costly PGM catalysts at comparable HER activity in neutral, acidic, or basic pH electrolytes.

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology,energy & fuels,electrochemistry
Hybrid Overlayer of Defective Ni-MOF and NiO Nanoparticles toward Efficient TiO2/CdS Type-II Heterojunction

Pai Peng,Jie Ren,Shuxiang Wang,Jing Huang,Li Zou,Pingping Yang,Xiangui Pang,Ming Zhang,Youyi Su,Wanqi Luo,Wenyan Tao,Jiale Xie

DOI: https://doi.org/10.1021/acs.langmuir.4c02426

IF: 3.9

2024-09-01

Langmuir

Abstract:The severe photocorrosion of cadmium sulfide (CdS) restricts its practical application for solar hydrogen production. Although remarkable progress has been achieved with an overlayer strategy for isolating the CdS surface, the lifetime of CdS-based photoanodes is still far from the actual requirements. Herein, a hybrid overlayer of defective Ni-MOF and NiO nanoparticles has been developed through the chemical bath deposition method with postannealing. This hybrid overlayer of Ni-MOF-d is coated on the surface of the TiO2/CdS type-II heterojunction. The composite photoanode exhibits a photocurrent density of 4.41 mA cm-2 at 1.23 VRHE, which is 3.47- and 1.32-fold that of CdS and TiO2/CdS, respectively. The Ni-MOF-d overlayer gives rise to a negative shift of the onset potential by 59.51 mV. After a long-term stability test of 11 h, a photocurrent retention of 70% is observed, which is among the most robust CdS-based photoanodes. The kinetics studies reveal that the performance improvements can be attributed to the multiple functions of the Ni-MOF-d hybrid overlayer, including isolating the CdS surface from the electrolyte, cocatalyzing the electrode oxidation processes, passivating the surface defect states of CdS, and facilitating the charge injection from the photoanode to the electrolyte.
Defect Chemistry of Titanium Dioxide (Rutile). Progress Toward Sustainable Energy

Tadeusz Bak,SA Sherif,David StClair Black,Janusz Nowotny

DOI: https://doi.org/10.1021/acs.chemrev.4c00185

IF: 62.1

2024-10-27

Chemical Reviews

Abstract:This work, which overviews defect chemistry of TiO(2) (rutile), is focused on atomic-size structural defects that are thermodynamically reversible. Here it is shown that thermodynamics can be used in defect engineering of TiO(2)-based energy materials, such as photoelectrodes and photocatalysts. We show that surface segregation of defects leads to the building-up of new surface structures that are responsible for reactivity. Since rational design of surface properties requires in situ surface...

chemistry, multidisciplinary
Tuning Surface Defect States in Sputtered Titanium Oxide Electron Transport Layers for Enhanced Stability of Organic Photovoltaics

Mehrad Ahmadpour,Mariam Ahmad,Michela Prete,John Lundsgaard Hansen,Denys I. Miakota,William Greenbank,Yunlin Jacques Zheng,Michiel Top,Thomas Ebel,Horst-Günter Rubahn,Vida Turkovic,Stela Canulescu,Nadine Witkowski,Morten Madsen

DOI: https://doi.org/10.1021/acsami.4c00056

IF: 9.5

2024-03-27

ACS Applied Materials & Interfaces

Abstract:Nonfullerene acceptors (NFAs) have dramatically improved the power conversion efficiency (PCE) of organic photovoltaics (OPV) in recent years; however, their device stability currently remains a bottleneck for further technological progress. Photocatalytic decomposition of nonfullerene acceptor molecules at metal oxide electron transport layer (ETL) interfaces has in several recent reports been demonstrated as one of the main degradation mechanisms for these high-performing OPV devices. While...

materials science, multidisciplinary,nanoscience & nanotechnology
Photoanodes Based on TiO$_2$ and $α$-Fe$_2$O$_3$ for Solar Water Splitting Superior Role of 1D Nanoarchitectures and of Combined Heterostructures

Stepan Kment,Francesca Riboni,Sarka Pausova,Lei Wang,Lingyun Wang,Hyungkyu Han,Zdenek Hubicka,Josef Krysa,Patrik Schmuki,Radek Zboril

DOI: https://doi.org/10.1039/C6CS00015K

2020-04-15

Abstract:Solar driven photoelectrochemical water splitting (PEC-WS) using semiconductor photoelectrodes represents a promising approach for a sustainable and environmentally friendly production of renewable energy vectors and fuel sources, such as dihydrogen (H2). In this context, titanium dioxide (TiO$_2$) and iron oxide (hematite, $\alpha$-Fe$_2$O$_3$) are among the most investigated candidates as photoanode materials, mainly owing to their resistance to photocorrosion, non-toxicity, natural abundance, and low production cost. Major drawbacks are, however, an inherently low electrical conductivity and a limited hole diffusion length that significantly affect the performance of TiO$_2$ and $\alpha$-Fe$_2$O$_3$ in PEC devices. To this regard, one-dimensional (1D) nanostructuring is typically applied as it provides several superior features such as a significant enlargement of the material surface area, extended contact between the semiconductor and the electrolyte and, most remarkably, preferential electrical transport that overall suppress charge carrier recombination and improve TiO$_2$ and $\alpha$-Fe$_2$O$_3$ photo-electrocatalytic properties. The present review describes various synthetic methods, properties and PEC applications of 1D-photoanodes (nanotubes, nanorods, nanofibers, nanowires) based on titania, hematite, and on $\alpha$-Fe$_2$O$_3$/TiO$_2$ heterostructures. Various routes towards modification and enhancement of PEC activity of 1D photoanodes are also discussed including doping, decoration with co-catalysts and heterojunction engineering. Finally, the challenges related to the optimization of charge transfer kinetics in both oxides are highlighted.

Applied Physics,Materials Science
Defect segregation and its effect on the photoelectrochemical properties of Ti-doped hematite photoanodes for solar water splitting

Barbara Scherrer,Tong Li,Anton Tsyganok,Max Döbeli,Bhavana Gupta,Kirtiman Deo Malviya,Olga Kasian,Nitzan Maman,Baptiste Gault,Daniel A. Grave,Alexander Mehlman,Iris Visoly-Fisher,Dierk Raabe,Avner Rothschild

DOI: https://doi.org/10.1021/acs.chemmater.9b03704

2020-12-08

Abstract:Optimising the photoelectrochemical performance of hematite photoanodes for solar water splitting requires better understanding of the relationships between dopant distribution, structural defects and photoelectrochemical properties. Here, we use complementary characterisation techniques including electron microscopy, conductive atomic force microscopy (CAFM), Rutherford backscattering spectroscopy (RBS), atom probe tomography (APT) and intensity modulated photocurrent spectroscopy (IMPS) to study this correlation in Ti-doped (1 cat.%) hematite films deposited by pulsed laser deposition (PLD) on F:SnO2 (FTO) coated glass substrates. The deposition was carried out at 300 °C, followed by annealing at 500 deg C for 2 h. Upon annealing, Ti was observed by APT to segregate to the hematite/FTO interface and into some hematite grains. Since no other pronounced changes in microstructure and chemical composition were observed by electron microscopy and RBS after annealing, the non-uniform Ti redistribution seems to be the reason for a reduced interfacial recombination in the annealed films, as observed by IMPS. This results in a lower onset potential, higher photocurrent and larger fill factor with respect to the as-deposited state. This work provides atomic-scale insights into the microscopic inhomogeneity in Ti-doped hematite thin films and the role of defect segregation in their electrical and photoelectrochemical properties.

Chemical Physics
New Insights into Defect‐Mediated Heterostructures for Photoelectrochemical Water Splitting

Xiaoqiang An,Tong Li,Bo Wen,Junwang Tang,Ziyu Hu,Li-Min Liu,Jiuhui Qu,C. P. Huang,Huijuan Liu

DOI: https://doi.org/10.1002/aenm.201502268

IF: 27.8

2016-01-01

Advanced Energy Materials

Abstract:Understanding the interfacial electronic structures of heterojunctions, a challenging undertaking, is extremely important to the design of photoelectrodes for efficient water splitting. The heterostructured interfaces in terms of crystal defects at the atomic‐level exemplified by TiO2/BiVO4 are studied. Results from both experimental observations and theoretical calculations clearly confirm the spontaneous formation of defective interfaces in the heterostructures. TiO2/BiVO4 junction with engineered interfacial defects can efficiently increase the carrier density and extend the lifetime of electrons. The inherent phenomenon of defective electronic structures in different heterostructures creates a significant impact on their photoelectrochemical performance. The synergetic effect between defect‐mediated mechanism and organic quantum dots sensitization yields significantly increased photoconversion efficiency, which is even superior to that of common metal sulfide sensitized ones. This result demonstrates an approach worthy for the design and fabrication of defect‐mediated heterostructures for water splitting, without utilizing harmful metal sulfides. Moreover, new insights into the influence of intrinsic defects on the interfacial charge transfer process between two different semiconductors for energy‐related applications have also been provided.
Black Defect-Engineered TiO2 Nanocrystals Fabricated Through Square-Wave Alternating Voltage As High-Performance Anode Materials for Lithium-Ion Batteries

Yingchang Yang,Wei Shi,Shijia Liao,Renhui Zhang,Senlin Leng

DOI: https://doi.org/10.1016/j.jallcom.2018.02.309

IF: 6.2

2018-01-01

Journal of Alloys and Compounds

Abstract:Black defect-engineered TiO2 nanocrystals have been successfully fabricated via electrochemical square-wave alternating voltage method. Repeated redox of Ti foil surface accompanying vigorous hydrogen evolution plays a key role on the formation of the black TiO2 nanocrystals. Transmission electron microscopy, X-ray photoelectron spectroscopy, X-ray diffraction, and Brunauer-Emmett-Teller specific surface area are utilized to characterize the structure and properties of the products. When utilized as anode materials for lithium-ion batteries, the black TiO2 nanocrystals electrode exhibits a high reversible capacity of 271 and 266 mAh g(-1) after 200 cycles at 0.5 C (1 C = 168 mA g(-1)), as well as a good rate capability, which are likely to be associated with small particle size (ca. 6 nm), surface/interfacial pseudocapacitive lithium storage and increased electronic conductivity contributed from Ti3+ defects. (C) 2018 Elsevier B.V. All rights reserved.

Defects Give New Life to an Old Material: Electronically Leaky Titania as a Photoanode Protection Layer

Titanium oxide crystallization and interface defect passivation for high performance insulator-protected Schottky junction MIS photoanodes.

Hole-Selective Hybrid TiO2 Layer towards Long-Term Stability of Low-Cost Photoanodes in Solar Water Oxidation

Defect-Tolerant TiO 2 -Coated and Discretized Photoanodes for >600 h of Stable Photoelectrochemical Water Oxidation

Interplay between Collective and Localized Effects of Point Defects on Photoelectrochemical Performance of TiO2 Photoanodes for Oxygen Evolution

PPy‐encapsulated SnS2 Nanosheets Stabilized by Defects on a TiO2 Support As a Durable Anode Material for Lithium‐Ion Batteries

Defect Engineering for Photocatalysis: From Ternary to Perovskite Oxynitrides

Sputter-Coated TiO 2 Films as Passivation and Hole Transfer Layers for Improved Energy Conversion with Solar Fuel WO 3 /CuWO 4 Photoanodes

Highly Enhanced Photoelectrocatalytic Properties by Α-Fe 2 O 3 Modified NF-TiO 2 Pyramids with Dominant (101) Facets

A Dual-Layer Titania Film with Enhanced Photocatalytic Activity

Electronic defects in metal oxide photocatalysts

An ultrathin amorphous defective co-doped hematite passivation layer derived via an in situ electrochemical method for durable photoelectrochemical water oxidation

Operandoelectrochemical Study of Charge Carrier Processes in Water Splitting Photoanodes Protected by Atomic Layer Deposited TiO2

TiO 2 /TiN Interface Enables Integration of Ni 5 P 4 Electrocatalyst with a III–V Tandem Photoabsorber for Stable Unassisted Solar-Driven Water Splitting

Hybrid Overlayer of Defective Ni-MOF and NiO Nanoparticles toward Efficient TiO2/CdS Type-II Heterojunction

Defect Chemistry of Titanium Dioxide (Rutile). Progress Toward Sustainable Energy

Tuning Surface Defect States in Sputtered Titanium Oxide Electron Transport Layers for Enhanced Stability of Organic Photovoltaics

Photoanodes Based on TiO$_2$ and $α$-Fe$_2$O$_3$ for Solar Water Splitting Superior Role of 1D Nanoarchitectures and of Combined Heterostructures

Defect segregation and its effect on the photoelectrochemical properties of Ti-doped hematite photoanodes for solar water splitting

New Insights into Defect‐Mediated Heterostructures for Photoelectrochemical Water Splitting

Black Defect-Engineered TiO2 Nanocrystals Fabricated Through Square-Wave Alternating Voltage As High-Performance Anode Materials for Lithium-Ion Batteries