Abstract:Introduction. Multilayer high-temperature coatings obtained using plasma spraying, are studied. The combination of layers of different chemical and phase compositions made it possible to increase wear resistance by 1.5–2.0 times. The purpose of this work is to study the influence of the chemical composition of sprayed coatings on the phase composition, structure, micromechanical and tribological characteristics under conditions of dry sliding friction of surface layers. Materials and methods of research. Coatings A and B consist of sequentially sprayed layers. The first and second layers were sprayed in a reducing atmosphere: the first layer was a heat-resistant self-fluxing powder of two systems: 1 – Fe-Cr-Si-Mn-B-C for coating A and 2 – Fe-Ni-Si-Mn-B-C for coating B; the second layer was a mixture of self-fluxing powder with iron powder in a 1:1 ratio. The third layer was obtained by spraying iron powder in an oxidizing atmosphere to form a metal oxide coating. To create a layer of scale on the surface, coated specimens were subjected to high-temperature annealing at a temperature of 1,000 °C. The chemical composition and nature of the distribution of elements over the thickness of the coatings were determined by micro-X-ray spectral analysis using a TWSCAN scanning electron microscope with an Oxford energy-dispersive attachment. Microhardness and micromechanical properties were studied using an instrumental microhardness tester of the Fischerscope HM2000 XYm system at a load of 0.980 N. Determination of tribological properties was carried out on a laboratory installation using the “finger-disc” scheme at loads of 30, 75, 100 and 130 N. To measure roughness parameters and obtain 3-D profilometry of surfaces after testing, a non-contact profilometer-profiler Optical profiling system Veeco WYKO NT 1100 was used. Results and discussion. Metallographic studies have shown that the formed multilayer coatings consist of an internal metal layer and an external oxide layer with a total thickness of the entire coating up to 800–850 μm. It is established that the first sprayed layer has the highest level of microhardness, which is due to the high-volume fraction of the strengthening phases contained in it (~ 95 %). It is shown that the coating A has increased wear resistance, which is expressed by minimal weight loss (~ 1.5 times less than that of the coating of the coatimg B), the friction coefficient was f = 0.3 for coating A and f = 0.4 for coating B. The study of wear surfaces has shown that for all selected test loads under sliding friction conditions, the coating of both compositions was preserved, even at a maximum load of 130 N.

Distribution on microhardness, chemical composition and structure over a layer of heat-resistant highyardness alloy formed by multilayer plasma surfacing in a nitrogen medium

Microhardness and Structure Distribution over the Layer of a High-Hardness Heat-Resitant Alloy Formed by Multi-Layer Plasma Surfacing in a Nitrogen Medium

Structure and properties of high-speed R2M9YuAT alloy formed by plasma surfacing in nitrogen with flux-cored wire

Chemical composition, structure and microhardness of multilayer high-temperature coatings

Evolution of Microstructure and Hardness of the Nitrided Zone during Plasma Nitriding of High-Alloy Tool Steel

Effect of Tempering on Structure and Properties of Plasma Surfacing of R2M9U High-Speed Tool Steel

Structural features and tribological properties of multilayer high-temperature plasma coatings

Heat Resistance of Surface Layers Obtained by Electron Beam Surfacing with Cr–B Powder Mixtures

Effect of Molybdenum Electron-Beam Cladding on the Heat and Wear Resistances of Surface Layers of Chromium-Nickel Austenitic Steel 12Kh18N9T

Investigation of Microstructure and Mechanical Performance of IN738LC Superalloy Thin Wall Produced by Pulsed Plasma Arc Additive Manufacturing

Structure and Properties of Surfacing Made of High-Entropy High-Speed Steel

Multi-Scale-Structured Composite Coatings by Plasma-Transferred Arc for Nuclear Applications

Microstructures and Mechanical Performance of Plasma-Nitrided Al 0.3 CrFe 1.5 MnNi 0.5 High-Entropy Alloys

Formation and Analysis of Multilayer Multielement Nanostructured Metal Films

Transformation of the nickel aluminide alloy structure through the application of a heat-resistant coating using oscillation electrode surfacing

Structure and Hardness of Nickel-based Alloy Plasma Arc Surfacing

Surface Characteristics and High-Temperature Wear of Plasma Nitrided Layer on Steel H13

Structure and Properties of a High-Entropy AlCrFeCoNi Alloy after Treatment with an Electron–Ion Plasma

Microstructure Evolution of FeNiCoCrAl1.3Mo0.5 High Entropy Alloy during Powder Preparation, Laser Powder Bed Fusion, and Microplasma Spraying

Wear-resistance Performance of Spray-welding Coating by Plasma Weld-surfacing

Formation and Precipitation Phases of Ni-Al System Intermetallic Surfacing Layers by Light Beam Heating