Abstract:Strike-slip fault zones commonly display complex 3D geometries, with high structural variability along strike and with depth and their architecture and evolution are difficult to analyse. In this regard, analogue modelling represents a powerful tool to investigate the structural, kinematic and mechanical processes in strike-slip fault systems with variable scales. In detail, dynamically scaled experiments allow the direct comparison between model and nature. The geometrical scale factor defines the model resolution, in terms of model/prototype length equivalence, and depends on the physical properties of prototype and model material. Therefore, the choice of the analogue material is critical in scaled analogue experiments. Granular materials like dry silica sand are ideal for the simulation of upper crustal deformation processes due to similar non-linear strain-dependent deformation behaviour of granular flow and brittle rock deformation. Comparing the geometrical scaling factor of the common analogue materials applied in tectonic models, we identified a model resolution gap for the simulation of fault-fracture processes corresponding to the structural scale (1 m &#8211; 100 m) observed in fault zones and damage zones in outcrops, field studies or subsurface well data. We developed a new Granular Rock-Analogue Material (GRAM) for the simulation of fault-fracture processes at the structural scale. GRAM is an ultra-weak sand aggregate composed of silica sand and hemihydrate powder capable to deform by tensile and shear failure under variable stress conditions. Based on dynamical shear tests, the new GRAM is characterised by a similar stress-strain curve as dry silica sand and has a geometrical scaling factor L*= Lmodel/Lnature = 10-3 (1 cm in model = 20 m in nature). We performed strike-slip experiments at two different length scales, applying as model material dry silica sand and the new GRAM. Digital Image Correlation (DIC) time-series stereo images of the experiments surface allowed the comparison of the developed structures at different stages of dextral displacement above a single planar basement fault. The analysis of fractures localisation and growth in the strike-slip zone with displacement and strain components enabled the comparison of the different structural styles characterising dry silica sand and GRAM models. The application of the developed GRAM in scaled experiments can provide new insights to the multi-scale investigation of complex deformation processes with analogue models.&#160;

Laboratory Observation and Micromechanics-Based Modelling of Sandstone on Different Scales

Multiscale Modeling and Analysis of Compaction Bands in High-Porosity Sandstones

Three-dimensional Discrete Element Simulation of the Triaxial Cyclic Loading of Sandstone Based on a Nonlinear Parallel-Bonded Stress Corrosion Model

Experimental investigation and micromechanical modeling of the brittle-ductile transition behaviors in low-porosity sandstone

Micromechanics-based multimechanism bounding surface model for sands

Strain-softening model for granite and sandstone based on experimental and discrete element methods

A Numerical Meso-Scale Elasto-Plastic Damage Model for Modeling the Deformation and Fracturing of Sandstone Under Cyclic Loading

Experimental and numerical investigations on the mechanical behavior of sandstone subjected to gas undrained triaxial compression

Investigation of compressive and tensile behaviors for porous sandstone by a microstructure-based constitutive model

Study on the correlation and calibration of macro and micro parameters of discrete element model for sandstone

Cross-scale Characterization of Sandstones Via Statistical Nanoindentation: Evaluation of Data Analytics and Upscaling Models

Constitutive Model and Microscopic Mechanism for Sandstone Strength Softening Damage

An error-correction analysis of scaled model for mode-I fracture toughness of sandstone under impact load

Experimental Investigation and Micromechanical Modeling of Elastoplastic Damage Behavior of Sandstone

Grain-scale failure mechanism of porous sandstone: An experimental and numerical FDEM study of the Brazilian Tensile Strength test using CT-Scan microstructure

Numerical study on sandstone strength and failure characteristics with heterogeneous structure

Analogue modelling of strike-slip tectonics from basin to structural-scale comparing silica sand and new rock-analogue materials

Mode-I failure and mechanical behavior of sandstone under cyclic loading: Laboratory testing and DEM simulation

Mechanical Properties and DEM-Based Simulation of Double-Fractured Sandstone under Cyclic Loading and Unloading

Micro-mechanical analysis of the effects of stress cycles on the dynamic and static mechanical properties of sandstone

A novel obtaining method and mesoscopic mechanism of pseudo-shear strength parameter evolution of sandstone