Abstract:In wire electrical discharge machining (WEDM), increasing the machining characteristics is always a research hot spot. Now, magnetic-assisted method cannot directly improve the performance of WEDM during machining magnetic material. In addition, due to the defects of convergence precision, convergence speed, global optimization, and subjectivity, the application of individual parameter optimization algorithm is limited. In order to address these problems, this paper proposes magnetic-assisted method and modified non-dominated neighbor immune algorithm to ameliorate the performance of WEDM in trim cutting magnetic material. Firstly, the force analysis of debris and the analysis of discharge current waveform are carried out to clarify what setting condition of the magnetic field generator is proper. It is indicated that the magnetic-assisted method maybe improves the machining characteristics of WEDM when the Lorentz force has the same direction with dielectric flashing force during trim cutting magnetic material. Additionally, a set of trim cutting Taguchi experiment is accomplished to investigate the effect of magnetic-assisted method on material remove rate (MRR), surface roughness (SR), and recast layer thickness (RLT). Thereinto, it can be found that the machining characteristics of WEDM are obviously improved by magnetic-assisted method. More specifically, under magnetic-assisted method, MRR, SR, and RLT are improved by an average of 18.45, 17.86, and 17%, respectively. Then, on the basis of game theory, the modified non-dominated neighbor immune algorithm (NNIA) is proposed to select best process parameters for further increasing the machining characteristics of magnetic-assisted WEDM (MA-WEDM). Eventually, the comparative results of three algorithms and verification experiment demonstrate that this modified NNIA exhibits better optimization performance than NSGA-II and NNIA. Specifically, by modified NNIA, the largest increase of MRR and the greatest decrease of SR and RLT are 22.37, 44.59, and 15.07%, respectively.

An experimental study for multi-pass cutting operation in wire electrical discharge machining of WC-5.3% Co composite

Complex taper profile machining of WC-Co composite using wire electric discharge process: analysis of geometrical accuracy, cutting rate, and surface quality

Analysis of Wire-cut Electric Discharge Machining Behaviour of AA6061 / C / ZrO2 Hybrid Nano Composites using Taguchi's method

Effect of Electrode Material and Hybrid Metaheuristic Optimization on Die Corner Accuracy during Wire Electrical Discharge Machining on Inconel (625): A Comparative Study

Experimental investigation on WEDG machining parameters for tungsten carbide

Evaluation of Wire Electrical Discharge Machining Performance Features on EN AW-6082 T6 Aluminum Alloy and Optimization of Machining Characteristics

Experimental investigation to assess the surface integrity in WEDM of Al-based hybrid composite material

Enhancing WEDM performance on Mg/FeCoCrNiMn HEA composites through ANN and entropy integrated COCOSO optimization

Experimental investigation on the surface quality of WEDM machined 20MnCr5 steel for Gear application

Use of RSM Desirability Approach to Optimize WEDM of Mild Steel

Machining performance analysis of wire-EDM for machining of titanium alloy using multi-objective optimization and machine learning approach

Performance Analysis of Wire Electrodes on Machining Ti-6Al-4V Alloy using Electrical Discharge Machining Process

Investigation of Machining Rate and Surface Roughness in Wire EDM of Al6063/WC/ZrO2 Composite using Response Surface Methodology

Optimization of Wire Electric Discharge Machining (WEDM) Process Parameters for AISI 1045 Medium Carbon Steel Using Taguchi Design of Experiments

Effect of Al7075 and Activated Carbon reinforced Composite on Optimizing WEDM Responses

Machinability and pulse characteristics of Ti-16Al-14Nb (α/β) alloy in wire-electric discharge machining process: A surface integrity study

Characterization of cast rare earth WE43 magnesium alloy and parameter optimization for wire electrical discharge machining using TOPSIS & COPRAS

Parametric investigation of W-EDM factors for machining AM60B conductive biomaterial

Magnetic-assisted Method and Multi-Objective Optimization for Improving the Machining Characteristics of WEDM in Trim Cutting Magnetic Material

An in-depth evaluation of surface characteristics and key machining responses in WEDM of aerospace alloy under varying electric discharge environments

A hybrid approach for machining optimization of the WEDM using grey-fuzzy with Metaphor-Less algorithms for Ti-3Al-2.5V