Abstract:Taking into account the local stresses resulting from the primary twinning with transformation strains, the competition between double twinning {10–11}–{10–12} and (10–12)–(–1012) (CDTW and EDTW) is theoretically modeled. Using electron backscatter diffraction technique, the statistical fractions, thickness-length ratios and their critical values of CDTW and EDTW within grains of as-cast AZ31 magnesium alloy sheets at the low strain stage of hot rolling processing are obtained to validate the theoretical results. In addition, the competition between the DTW and twin intersection are also discussed in detail. The results show that: (1) The secondary twin growth complies with the classical Hall-Petch relationship. Due to the difference in the driving forces resulting from different transformation strains between the primary extension and contraction twinning, the secondary extension twin of EDTW is more difficult to grow compared to that of CDTW for primary twin bands with small thickness-length ratios, which is contrary to the regulation for primary twin bands with large thickness-length ratios; (2) The greater the thickness-length ratio of the primary twinning is, the smaller the critical shear stress of the secondary twinning is. This is opposite to the effect of thickness-length ratio on the critical shear stress of the incident twinning in the twin intersection. It is indicated that the thickening of the primary twinning provides the higher driving force for the formation of DTW, however hinders the twin intersection more evidently; (3) Within coarse grains, at the low strain stage, the formation of DTW can dominantly induce dynamic recrystallization and continue plastic deformation, while the stress concentration resulting from the twin intersection is inclined to cause brittle fracture. Therefore, based on the effect of the local stress, the selection mechanism of the thickness-length ratio on the DTW and twin intersection is of great significance to determining the plastic performance of magnesium alloys during hot working. In the current study, massive control factors of the thickness-length ratio of the primary twinning are concluded, which provides some corresponding schemes of material design.

Effect of deformation twins on damping capacity in extruded pure magnesium

Enhanced damping capacity of magnesium alloys by tensile twin boundaries

Effect of pre-deformation on the activation stress of {10–12} twinning in Mg–3Al–1Zn alloy

Effect of twins and plastic-deformation anisotropy of extruded magnesium alloy on fatigue crack growth and crack closure behavior

Effect of twinning on the deformation behavior of an extruded Mg-Zn-Zr alloy during hot compression testing

Effect of texture on damping behaviour in ZK60 magnesium alloy

Evolution of deformation mechanisms and their orientation dependence in fine-grained Mg-3Gd during tension

Improvement in damping capacity of extruded pure magnesium through precompression and subsequent annealing: Effects of dislocation and twin boundary motions

Effects of deformation twins on microstructure evolution, mechanical properties and corrosion behaviors in magnesium alloys - A review

Effect of deformation conditions on twinning of AZ31 magnesium alloy during compression test

Towards understanding double extension twinning behaviors in magnesium alloy during uniaxial tension deformation

Effects of texture and twinning on the torsional behavior of magnesium alloy solid rod: A crystal plasticity approach in comparison with uniaxial tension/compression

Influence of precipitation on tension and compression twinning in Mg-6.5Zn alloy

Study of Twin Behavior During Uniaxial Compression of Az31 Magnesium Alloy

The Effect of Twins on Mechanical Properties and Microstructural Evolution in AZ31 Magnesium Alloy during High Speed Impact Loading

Effect of Local Stresses of Primary Twinning on Double Twinning, Twin Intersection and Their Competition

Texture weakening effect from { 10 1 ̅ 1 } twins induced static recrystallization in ambient extrusion AZ31 magnesium alloy

Towards revealing the relationship between deformation twin and fatigue crack initiation in a rolled magnesium alloy

The Effect of Tension Twin on the Dynamic Recrystallization Behavior in Polycrystal Magnesium by Atomistic Simulation

Proliferation of Twinning in HCP Metals: Application to Magnesium

Effect of Pre-Existing Twinning on Strain Localization During Deformation of a Magnesium Alloy