Abstract:Steel slag and phosphogypsum are industrial wastes produced during steelmaking and the wet phosphoric acid process, respectively, contributing to significant environmental challenges due to their low utilization rates. This study explores their combination with GBFS to develop a new ecofriendly cementitious material based on steel slag. The effects of initial factors on early properties were systematically investigated using an orthogonal test. Hydration and microstructural characteristics were obtained through analysis of hydration processes, product characteristics, microstructure, and pore structure, and hydration behaviors were postulated. The findings reveal that a lower steel slag-GBFS ratio leads to a higher strength of the composite system. A higher water-binder ratio leads to a longer setting time and greater fluidity. The composite exhibits a low exothermic reaction, characterized by three exothermic peaks on its hydration heat release curve. The primary hydration products are Ettringite and C-(A)-S–H gel. Gypsum acts as an intermediate product. The main reaction in the composite system is that bassanite first transforms into gypsum. Concurrently, the [SiO 4 ] 4− , and [AlO 4 ] 5− in steel slag and GBFS gradually depolymerize. Once the conversion of hemihydrate gypsum is completed, the gypsum begins to dissolve, forming the primary hydration products. As hydration progresses, the system gradually forms a structure where ettringite intertwines, with gel filling and encapsulating the ettringite. The composite exhibits a loose pore structure in the early stages, leading to lower mechanical performance. Strength increases rapidly from 3 to 7 d. In the later hydration stages, the volume of harmful pores increases again, which subsequently moderates the strength gain. Nevertheless, under optimal conditions, compressive strength reaches 34.1 MPa at 28 d.

Study on the Mix Proportion Design of C30 Supersulphated Phosphogysum-Slag Cement (SSC) Concrete

Development of Sustainable Self-Compacting Concrete Using Recycled Concrete Aggregate and Fly Ash, Slag, Silica Fume

Understanding the Role of Calcium Silicate Slag in Sodium Carbonate-Activated Green Materials: Influence on Kinetics, Strength, and Efflorescence

Hydration behavior and strength development of supersulfated cement prepared by calcined phosphogypsum and slaked lime

Mechanical properties and hydration mechanism of super-sulfated cement prepared with ordinary Portland cement, carbide slag, and sodium silicate

An Eco-Friendly Phosphogypsum-Based Cementitious Material: Performance Optimization and Enhancing Mechanisms

The mechanical properties of supersulphated cement containing phosphogypsum

The Influence and Application of Slag, Fly Ash, and Limestone Flour on Compressive Strength of Concrete Based on the Concrete Compressive Strength Development over Time (CCSDOT) Model

A study on super-sulfated cement using Dinh Vu phosphogypsum

Effect of modified phosphogypsum on the hydration properties of the phosphogypsum-based supersulfated cement

Research on Sustainable Development of Fine-Grained Material Cement Slurry

A New Model to Predict the Optimal Mix Design of Self-Compacting Concrete Considering Powder Properties and Superplasticizer Type

Experimental study on strength and abrasion-resistance enhancement admixture

The Optimization of Mix Proportion Design for SCC: Experimental Study and Grey Relational Analysis

Preparation, mechanism, and application of silica fume–steel slag composite cementitious material based on the D-optimal mixture method

Preparation and Mechanical Performance of Supplementary Cementing Materials Cementitious by Electroplating Sludge

Preparation of steel slag-based cementitious materials compounded with GBFS and phosphogypsum: mix design, hydration, and microstructure characteristic

Preparation and Hydration Properties of Steel Slag-Based Composite Cementitious Materials with High Strength

Hydration mechanism of calcium sulfoaluminate-activated supersulfated cement

MgO-based supersulfated cement with different industrial by-product gypsum: Experiments and molecular dynamics simulation

Laboratory Preparation and Performance Characterization of Steel Slag Ultrafine Powder Used in Cement-Based Materials