Abstract:PHPs (pulsating heat pipes) are widely used as an efficient heat transfer element in equipment thermal management and waste heat recovery due to their flexibility. The purpose of this study was to design a heat transfer device that utilizes an asymmetric pulsating heat pipe structure by adjusting the lengths of selected pipes within the entire circulation pipeline. In the experiment, a constant temperature water bath was used as the heat source, with heat dissipated in the condensing section via natural convection. An infrared thermal imager was used to record the temperature of the condensing section, and the local wall temperature distribution was measured in different channels of the condensing section. Based on an in-depth analysis of the wavelet frequency, the following research conclusions are drawn: Firstly, as the heat source temperature increases, the start-up time of the pulsating heat pipe is shortened, the operating state changes from start–stop–start to stable and continuous oscillation, and the oscillation mode changes from high amplitude and low frequency to low amplitude and high frequency. These changes are especially pronounced when the heat source temperature is 80 °C, which is when the thermal resistance reaches its lowest value of 0.0074 K/W, and the equivalent thermal conductivity reaches its highest value of 666.29 W/(m·K). Secondly, the flow and oscillation of the working fluid can be effectively promoted by appropriately shortening the length of the condensing section of the pulsating heat pipes or the heat transfer distance between the evaporation and condensing sections. Third, under a low-temperature heat source, the oscillation frequency of each channel of a pulsating heat pipe is found to be low based on wavelet analysis. However, as the heat source temperature increases, the energy content of the temperature signal of the working fluid in each channel changes from a low- to a high-frequency value, gradually converging to the same characteristic frequency. At this point, the working fluid in the pipes no longer flows randomly in multiple directions but rather in a single direction. Finally, we determined that the maximum oscillation frequency of working fluid in a PHP is around 0.7 HZ when using the water bath heating method.

The Impact of Variation in Filling Ratios, Evacuation Pressure, and Heat Input on Thermal Performance of Pulsating Heat Pipe

Experimental Investigation on the Temperature Distribution Characteristics of the Evaporation Section in a Pulsating Heat Pipe

Investigation on the Influence of Different Heat Transmission Distances on Thermo-Hydrodynamic Characteristics of Pulsating Heat Pipes

Experimental Research on Heat Transfer Performance of 3 mm Closed Pulsating Heat Pipe

Experimental Research on the Start-Up Characteristics and Heat Transfer Performance of Pulsating Heat Pipes with Rectangular Channels

Review of the Development of Pulsating Heat Pipe for Heat Dissipation

Experimental investigation on heat transfer performance of closed-loop pulsating heat pipe with large inner diameter

Numerical Study of the Thermal Performance of a Hydrogen Pulsating Heat Pipe

Transient Numerical Model on the Design Optimization of the Adiabatic Section Length for the Pulsating Heat Pipe

Partial Visualization Study on Flow, Startup and Heat Transfer Characteristics of Closed-Loop Pulsating Heat Pipe with R1336mzz(Z)

Experimental investigation on thermal performance of pulsating heat pipe by using Dowtherm – A

Experimental Study on the Thermo-Hydrodynamic Characteristics of a Nitrogen Pulsating Heat Pipe

Evaporating Temperature Uniformity of the Pulsating Heat Pipe with Surfactant Solutions at Different Concentrations

Experimental Investigation on the Heat Transfer Performance and Evaporation Temperature Fluctuation of a New-Type Metal Foam Multichannel Heat Pipe

Experimental Study on a Hydrogen Closed-Loop Pulsating Heat Pipe with Two Turns

Experimental Study of Thermal Performance of Pulsating-Heat-Pipe Heat Exchanger with Asymmetric Structure at Different Filling Rates

Evaluation of the Heat Transfer Performance of a Device Utilizing an Asymmetric Pulsating Heat Pipe Structure Based on Global and Local Analysis

Numerical Investigation on Pulsating Heat Pipes with Nitrogen or Hydrogen

Study of an asymmetric dual loop pulsating heat pipe: Visualization and parametric analysis

Thermo-hydrodynamic Analysis of a Nitrogen Flat-Plate Pulsating Heat Pipe Using CFD Modeling and Visualization Experiments

Thermal performance of concentrically arranged two interconnected single-loop pulsating heat pipes