Abstract:Shape memory alloys are used in diverse fields. It is Ni–Ti alloys that are predominantly used for applications capitalizing on the functional properties of shape memory and superelastic effect. These properties are influenced by factors, such as alloy composition, alloying addition, thermal and mechanical treatment, etc. In any application, the transformation temperatures of the alloy/device are very critical. Moreover, the stability of transformation temperatures and a smaller hysteresis are preferred. Ni–Ti alloys have their own limitations, such as low transformation temperatures and lack of ductility. In order to overcome these limitations, researchers have used ternary additions, such as Zr, Hf, Cu, Pd and Au. The use of copper is practicable because of its lower cost as compared to Ti and Ni. Substitution of Cu for Ni up to ~ 25% in an equiatomic NiTi alloy causes it to exhibit SME. The transformation temperatures of NiTiCu exhibit less sensitivity to composition and a smaller thermal hysteresis. In this work, therefore, the effect of methods of quenching on transformation temperatures and microstructure of an Ni–Ti–4Cu (at.%) alloy has been explored. The material was cast using vacuum induction melting. It was solutionized at 950 °C for 2 h and cooled using different methods/quenchants: liquid nitrogen, water at room temperature, air, annealing (furnace cooling). The samples quenched by different techniques were characterized by XRD, DSC, OM, SEM and hardness test. The results indicated that the martensite plate size varied in samples quenched using different quenchants even though the morphology was the same in all specimens. In addition, the transformation temperatures and hardness values of the alloy specimens varied as the intensity of quenching varied. The results are presented and discussed in detail in the paper.

Effects of Quenching Media on Phase Transformation Characteristics and Hardness of Cu-Al-Ni-Co Shape Memory Alloys

The Effect of Annealing Temperature and Quenching Media Variations On Heat Treatment Process of Cu-Zn-Al Shape Memory Alloys For Shape Memory Effect and Microstructure

The Effect of Quenching Methods on Transformation Characteristics and Microstructure of an NiTiCu Shape Memory Alloy

Effects of Quenching Temperatures on Microstructure, Phase Transformation Characteristics and Shape Memory Behaviors of CuAlTa and CuAlTaNb HTSMAs

Effect of Homogenization on the Transformation Temperatures and Mechanical Properties of Cu15Ni35Hf12.5Ti25Zr12.5 and Cu15Ni35Hf15Ti20Zr15 High-Entropy Shape Memory Alloys

Influence of Heat Treatment on Microstructures and Shape Memory Effect of Cu-28Zn-2.5Al wt. % Produced by Gravity Casting

Phase Transformation and Precipitation in Aged Ti–Ni–Hf High-Temperature Shape Memory Alloys

Martensitic transformation characteristics, mechanical properties and damping behavior of Cu–Al–Ni shape memory alloys: A review of their modifications and improvements

Influence of copper addition on the properties of equiatomic NiTi shape memory alloy prepared by vacuum induction melting method

Structural and Phase Transformations and Physical and Mechanical Properties of Cu-Al-Ni Shape Memory Alloys Subjected to Severe Plastic Deformation and Annealing

Phase transformation and microstructure of quaternary TiNiHfCu high temperature shape memory alloys

Effect of Material State on the Phase Transformation of NiTi Shape Memory Alloy

Effect of heat treatment on shape memory properties of ductile CuAlMn alloys

Microstructure and martensitic transformation behavior of CuAlNb high temperature shape memory alloy

A Microstructural Study of Cu-10Al-7Ag Shape Memory Alloy in As-Cast and Quenched Conditions

Effect of Heating/Cooling Rate on the Transformation Temperatures in Tinicu Shape Memory Alloys

Influence of Heat Treatment on Phase Transformation of NiTi Shape Memory Alloys

Effects Of Parent Phase Aging And Thermal Cycling On Shape Memory Characteristics In A Cu-Zn-Al Alloy

Microstructural features, martensitic transformation, and functional properties of multicomponent Ti–Ni based shape memory alloys

Thermal Cycling Effect In Cu-11.9al-2.5mn Shape Memory Alloy With High M-S Temperature

Effect of alloying elements (Nb, Ag) on the damping performance of Cu–Al–Mn shape memory alloys