Abstract:Laser drilling is always accompanied by recast layers, micro-cracks, and heat-affected zones, which limit its application in engineering. Due to its unique advantages, such as no heat-affected zones, no residual stresses, and no dependence on the mechanical properties of the materials, electrochemical dissolution has been adopted to remove the laser drilling-induced surface defects. The electrochemical dissolution characteristics and surface evolution of the laser-drilled Ni-based superalloys were studied. The polarization curves and electrochemical impedance spectroscopy (EIS) of the laser-drilled materials and the substrate were measured, indicating that the laser-drilled surface had a smaller corrosion resistance than the original substrate. X-ray photoelectron spectroscopy (XPS) results showed that the laser-drilled surface had a much higher oxygen content than the substrate. Additionally, electric current efficiency curves were obtained to study the anodic dissolution behavior of Ni-based superalloys. An electric current density in the 5–40 A/cm2 range was preferred to enhance the electrochemical dissolution rate. Moreover, the effects of electric current densities and post-processing time on the surface roughness and the recast layer thickness of the laser-processed Ni-based superalloys were investigated using a NaCl and NaNO3 solution electrolyte. The evolution of the surface quality and recast layer thickness were clarified. Furthermore, an anodic dissolution model of the laser-processed surface was established to illustrate the electrochemical post-processing mechanisms. Results revealed that electrochemical dissolution could completely remove the laser drilling-induced surface defects in 20 s using a 12.5 wt.% NaNO3 solution electrolyte and a 40 A/cm2 electric current density. Finally, an electrochemical post-processed surface with surface roughness (Ra) of 1.7 µm and without a recast layer was achieved. Micro holes without recast layers and Ra of 0.69 µm were obtained with high efficiency using laser processing and electrochemical post-processing.

Assessment of surface integrity of Ni superalloy after electrical-discharge, laser and mechanical micro-drilling processes

Surface Integrity of Inconel 718 in High-Speed Electrical Discharge Machining Milling Using Air Dielectric

Impact of Process Parameters on the Quality of Deep Holes Drilled in Inconel 718 Using EDD

Surface Morphology Analysis of Inconel 625 through Multi-walled Carbon Nanotubes-Based Electric Discharge Machining

A comparative assessment in sequential μ-drilling of Hastelloy-X using laser in combination with μ-EDM and μ-ECM

Evaluation of surface integrity after high energy machining with EDM, laser beam machining and abrasive water jet machining of alloy 718

Characterization and Parametric Optimization of Micro-hole Surfaces in Micro-EDM Drilling on Inconel 718 Superalloy Using Genetic Algorithm

High Speed EDM and Laser Drilling of Aerospace Alloys

Inconel 625 sustainable milling surface integrity and the dependence on alloy processing route

Surface roughness optimization of hybrid PBF-LB/M-built Inconel 718 using in situ high-speed milling

Optimizing Hole Shape and Improving Surface Quality of Inconel 718 Alloy by High-Temperature Chemical Assisted Laser Processing

Effect of heat treatment on the morphology and mechanical properties of the novel Ni-based superalloy with machinability assessment through electrical discharge machining

Study on anodic dissolution behavior and surface evolution of laser-drilled Ni-based superalloys during electrochemical post-processing

Surface integrity of holes machined by electrochemical discharge drilling method

Comparison of drilling of Inconel 625 by AWJM and WEDM

Experimental exploration and optimization of dual-channel electrode micro-drilling in Inconel 617 using electrical discharge machining

Experimental investigation of magnetic-field-assisted electric discharge machining by silicon-based dielectric of Inconel 706 superalloy

A comparative study on drillability of Inconel 625 alloy fabricated by wire arc additive manufacturing

Evaluation of WEDM performance characteristics of Inconel 706 for turbine disk application

Ultrafast drilling of Inconel 718 using hybrid EDM with different electrode materials

Experimental study of nickel-based superalloy IN792 with femtosecond laser drilling method