Abstract:Nowadays, pumps of different size are needed for a great variety of purposes. In the past, both computational fluid dynamics (CFD) and experimental flow visualization were performed to reveal flow characteristics within centrifugal pumps, to examine a specific design and to guide design improvement (see Burgreen et al. 1996, 2000). Li et al. (2007) studied the interior viscous flow in a mini pump with an asymmetric axis using CFD and PIV (particle image velocimetry) for improvement of the pump design. Matsui et al. (2002) adopted the the k-ω model in the CFD simulation for a centrfugal pump, and the computational grid system only consisted of one flow passage for LDV (laser Dopler velocimetry) test impeller. Byskov et al. (2003a) and Pedersen & Larsen (2003 b) investigated the flow inside the rotating passages of a six-bladed shrouded centrifugal pump impeller using LES simulation and PIV and LDV measurements. The velocities predicted with LES were in good agreement with the experimental data. The two RANS simulations were, however, not able to predict this complex flow field. It was thus found that using LES for analyzing the flow field in centrifugal pumps could shed light on basic fluid dynamic with a satisfactory accuracy compared to experiments. A transient simulation was used to study the effects of pulsatile blood flow due to the heartbeat through blood pumps by Song et al. (2003). The microsized geometry of the pump made the choice of turbulence models significant for the accuracy of calculation. The comparison showed that the k-ω model gave better predictions of the shear level within the near wall regions than the k-e model. Guleren and Pinarbasi (2004) indicated that the stallcell size extended from one to two diffuser passages. Comparisons of the computational results with experimental data were made and showed good agreement. The unsteady flow in a low specific speed radial diffuser was simulated by the CFD code CFX-10 by Feng et al. (2009). The PIV and LDV measurements had been conducted to validate the CFD results. Both the phase-averaged velocity fields and the turbulence fields obtained from different methods are presented and compared. In this study, in order to get more information about the internal flow of a centrifugal pump, both experimental measurement and numerical simulation are engaged. A centrifugal model pump test rig is built for PIV measurement. The test, involving the technology of index match and fluorescent, is for acquiring flow pattern in a fixed rotational speed, the velocity distribution of the flow field are thus obtained. And, the RANS (Reynolds

Theoretical Study and Measurement of the Characteristic Curves of a Centrifugal Pump

Experimental and numerical investigations on pressure pulsation in a pump mode operation of a pump as turbine

Influence of vane curve of solid liquid two-phase flow centrifugal pump on dynamic properties of fluid

Investigation of Turbulence Modeling in a High Speed Centrifugal Pump With an Inducer

Transient Internal Characteristic Study of a Centrifugal Pump During Startup Process

Experimental study of the characteristic curves of 0.5 HP radial pump with constant speed

Simulations and measurements of pump

Experimental study of a centrifugal pump operating as a hydraulic turbine

A New Prediction Method for the Complete Characteristic Curves of Centrifugal Pumps

Theoretical, Numerical and Experimental Research of Single Stage, Radial Discharge Centrifugal Pump Operating in Turbine Mode

Investigation on Inner Flow Quality Assessment of Centrifugal Pump Based on Euler Head and Entropy Production Analysis

Physical Modelling of the Set of Performance Curves for Radial Centrifugal Pumps to Determine the Flow Rate

Prediction Method for the Complete Characteristic Curves of a Francis Pump-Turbine

Four-quadrant Characterization of Hydrodynamic Phenomena in a Low Specific Speed Centrifugal Pump

Numerical Simulation on the Steady and Unsteady Internal Flows of a Centrifugal Pump

Numerical Simulation and Computational Flow Characterization Analyses of Centrifugal Pump Operating as Turbine

Experimental And Numerical Simulation On The Starting Period Of A Centrifugal Pump

A Comparative Study between Theoretical and Measured Performance of Standard Centrifugal Pumps Running as Turbines

Simulations And Measurements Of Dredge Pump

Prediction of centrifugal pump performance using energy loss analysis

Predicting pump-turbine characteristic curves by theoretical models based on runner geometry parameters