Abstract:Abstract The breakup of liquid films in high-speed flows is found in many applications. These include prefilming air blast atomization found in fuel injectors and shedding of droplet off of airfoils. In this work, a test rig has been developed and applied to study the breakup of water films from the trailing edge of an NACA 0012 airfoil placed in a high-speed air flow. The results provided reflect a new detailed dataset focused on air velocities above 75 m/s. Computational fluid dynamic (CFD) simulations were used to guide the development of the rig and the associated boundary and inlet conditions. In this work, air velocities up to 175 m/s were used with water films between 0.4 cm2/s and 3.6 cm2/s. The water film was introduced onto one surface through a series of 0.5 mm holes separated by 1 mm at a location 35 mm downstream of the leading edge of the vane. High speed video was used to document the sheet breakup behavior from the edge of the airfoil. Image analysis was used to identify the breakup length of ligaments formed. Laser diffraction was used 50 mm downstream of the trailing edge of the vane to determine the droplet size distribution and associated representative average diameters generated. A series of test conditions were run between 50 m/s and 175 m/s using multilevel factorial designed experiments. The results obtained were subjected to analysis of variance to generate correlations for breakup length and droplet representative diameters as a function of the conditions studied. The analysis was conducted on dimensionless versions of the variables studied to help connect the results to the physics of the situation. For example, rather than using air velocity to correlate the behavior, the Weber number (based on gas phase density and velocity) was used owing to its historical ability to describe liquid breakup processes. The results obtained are compared with other studies in the literature, and good agreement was found for the conditions at which a comparison could be made. It is observed that, for the conditions studied, liquid film thickness has little effect on the resulting droplet sizes—especially for the higher air velocity cases studied. The results also illustrate the sensitivity to choice of the characteristic length, which is generally consisted of trailing edge geometry or boundary layer thickness. In contrast, liquid film does influence the ligament breakup length, although the time to break up is less affected. Overall, the correlations developed provide engineering tools to help estimate ligament and drop size behavior for water films shed from airfoils in a high-speed flow.

Measurements of water film thickness on a wing surface in simulated heavy rain

Aerodynamic efficiency study of 2D airfoils and 3D rectangular wing in heavy rain via two-phase flow approach

Airfoil performance degradation by coupling effects of supercooled raindrop icing and heavy rainfall

Formulations of Hydrodynamic Force in the Transition Stage of the Water Entry of Linear Wedges with Constant and Varying Speeds

Numerical simulation of droplet impingement and film flow for three-dimensional wings

Experimental study and modeling of water film thickness in aero-engine under air–water mist flow

Numerical Simulation of Water Film Flow and Breakup on Anti-Icing Surface

A Numerical Study of Water Entry of Asymmetric Wedges Using a CIP-based Model

Liquid water content measurement with SEA multi-element sensor in CARDC icing wind tunnel: Calibration and performance

Analysis of Water Film Distribution and Aerodynamic Performances of High-Speed Train Under Rainfall Environment

Liquid film morphology and aerodynamic performance of a high-speed train under wind-rain environments

A Study of Formative and Continuous Models for Umbrella Water Curtain Based on Wall-Attaching Jets

Numerical study on the three-dimensional flow of water film on the outer surface of the hollow stationary blade

Film thickness measurement with an ultrasonic transducer

Finite volume based film flow and ice accretion models on aircraft wings

Assessment and improvement of rainfall environment reproduction for climatic wind tunnel

Three-dimensional high speed drop impact onto solid surfaces at arbitrary angles

Effects of Simulated Surface Roughness on Flow Characteristics in Symmetrical Airfoil

Investigation of Water Films Shed From an Airfoil in a High-Speed Flow

Experimental and modeling study on liquid film thickness of horizontal gas-liquid annular flow using ultrasonic method

Analysis of Numerical Methods for Droplet Impingement Characteristics under Aircraft Icing Conditions