Abstract:Alloy 800 is extensively used in nuclear power plants (NPPs) as steam generator tubing material and is essentially the pressure barrier between radioactive and non-radioactive components of the heat transport system in a NPP. Alloy 800 tubes are subjected to various surface finishing operations such as shot peening, pickling and passivation, and electropolishing before installing it in nuclear plants. The finishing operations carried out could cause a significant change in surface conditions that may alter the high-temperature oxidation behavior of Alloy 800. Surface finishing operations such as electropolishing, pickling and passivation and shot peening were carried out on Alloy 800. Surface roughness was measured for different surface-treated samples by using laser profilometer. The residual stress on the treated surface was quantified using grazing incidence x-ray diffraction (Sin 2 Ψ method). The microhardness measurements were carried out to evaluate the effect of strain hardening. All of the surface-treated specimens along with the as-received specimen were exposed in steam environment in an autoclave at 400 °C, 10 MPa for a period of 72 h. The difference in color of oxide film correlated with weight change of specimen having different surface treatments. It was observed that surface roughness, residual stress and hardness of the surface influence the oxidation behavior. The oxidation was more in the presence of tensile residual stress compared to compressive residual stress on Alloy 800. The morphology, orientation and composition of oxide layer thus formed during exposure to high-temperature steam were characterized using scanning electron microscopy (SEM), microlaser Raman spectroscopy (MLRS). The oxide film formation rate varied on Alloy 800 due to different surface finishing operations. The oxide film morphology and composition plays an important role in localized corrosion resistance of Alloy 800. The oxide film instability would result in local breakage which acts as a precursor for stress corrosion cracking (SCC) initiation on Alloy 800. This study establishes the influence of surface treatments and the residual stress generated on high-temperature steam oxidation of Alloy 800.

Long-term effects of a chemical decontamination procedure on the corrosion state of the heat exchanger tubes of steam generators

Development of a Multi-technique Characterization Portfolio for Stainless Steels Exposed to Magnox Reprocessing Liquors

An XPS and TEM study of the composition and structure of native oxides on the inner surface of as-received Ni base alloy steam generator tubes

Corrosion of Stainless Steel in Simulated Nuclear Reactor Primary Coolant—Experiments and Modeling

High-Temperature Degradation and Protection of Ferritic and Austenitic Steels in Steam Generators

Corrosion Mechanisms of 304L NAG in Boiling 9M HNO3 Containing Cr (VI) Ions

Decomposition products of oxygen scavengers and their effect on corrosion of steam generator materials – I. Diethyl-hydroxylamine and carbohydrazide

Investigation on High Temperature Corrosion of Water-Cooled Wall Tubes at a 300 MW Boiler

Corrosive damage analysis and characterization of boiler tubes in a secondary superheater

Investigating the Impact of Surface Finishing and Residual Stress on the Oxidation Behavior of Alloy 800

The effect of different surface treatments of 310S austenitic stainless steel on the corrosion behavior in supercritical water using slow positron methods

Field Studies of Steam Oxidation Behavior of Austenitic Heat-Resistant Steel 10Cr18ni9cu3nbn

Analysis of corrosion layers on protective coatings and high temperature materials in simulated service environments of modern power plants using SNMS, SIMS, SEM, TEM, RBS and X-ray diffraction studies

High Temperature Corrosion Resistance of Different Commercial Alloys Under Various Corrosive Environments

Molten sulphate vanadateinduced hot corrosion behaviour of YSZ-reinforced thermal spray coatings at elevated temperature

High-temperature corrosion of water-wall tubes in oxy-combustion atmosphere

Research in Alternating Corrosion on the Quench Oil/diluted Steamheat Exchanger Tubes of Ethylene Plant

Microbiologically influenced corrosion (MIC) in stainless steel heat exchanger

Corrosion surveillance program for tank, fuel cladding and supporting structure of 30 MW Indonesian RSG GAS research reactor

Comparative Study on the Corrosion Behavior of Materials in Heat Recovery Steam Generators for Combined Cycle Power Plant, Based on Sulfuric Acid Concentrations: Carbon Steels vs. Duplex Stainless Steel (UNS S32205)