Functional activated carbon: from synthesis to groundwater fluoride removal

Soumia Bakhta,Zahra Sadaoui,Nabil Bouazizi,Brahim Samir,Ouiza Allalou,Christine Devouge-Boyer,Melanie Mignot,Julien Vieillard

DOI: https://doi.org/10.1039/d1ra08209d

IF: 4.036

2022-01-01

RSC Advances

Abstract:Conversion and surface modification of date stems to obtain a relevant adsorbent to remove fluoride contamination.

chemistry, multidisciplinary

What problem does this paper attempt to address?

Nano-magnetically modified activated carbon prepared by oak shell for treatment of wastewater containing fluoride ion

Fatemeh Takmil,Hossein Esmaeili,Seyyed Mojtaba Mousavi,Seyyed Alireza Hashemi

DOI: https://doi.org/10.1016/j.apt.2020.06.015

IF: 4.969

2020-08-01

Advanced Powder Technology

Abstract:In this study, the adsorption of fluoride ion (F-) from synthetic wastewater was performed using activated carbon/Fe3O4 nanocomposite in a batch system. To prepare activated carbon (AC), oak shell was used. Also, several analyses such as BET, SEM, EDX, FTIR, XRD, VSM and DLS analyzes were used to study the structure and morphology of the AC/Fe3O4 nanocomposite. BET analysis indicated that the specific surface area of Fe3O4 and AC/Fe3O4 were 65.44 and 226.78 m2/g, respectively, which shows the surface area of the AC/Fe3O4 composite was significantly increased compared to Fe3O4. Also, the particle size of the AC/Fe3O4 composite was obtained 75 nm by the DLS analysis. The sorption tests indicated that the highest sorption efficiency of fluoride ion using the Fe3O4/AC nanocomposite was obtained 97.4%. Moreover, the experimental results were well fitted with the Freundlich model. The maximum monolayer uptake capacity using the AC/Fe3O4 was obtained as 454.54 mg/g and showed a remarkable adsorption capacity, whichever achieved for fluoride ion sorption. Also, zero-point charge of pH (pHzpc) was obtained 5. Furthermore, the kinetic data were described by the quasi-second-order model. Besides, the thermodynamic parameters showed that the uptake of fluoride ion with the AC/Fe3O4 nanocomposite was spontaneous, practical, and endothermic. The outcomes suggest that AC/Fe3O4 nanocomposite can be effectively applied for the F- ion removal from synthetic wastewater.

engineering, chemical
Synthesis and characterization of aluminum-based adsorbent and application in fluoride removal from aqueous solution

Jihane Assaoui,Zineb Hatim,Abdelmoula Kheribeche

DOI: https://doi.org/10.13171/mjc101020291172ja

2020-01-29

Mediterranean Journal of Chemistry

Abstract:A novel adsorbent was obtained by a facile precipitation method and was used for fluoride removal from aqueous solution. Mineralogical and physicochemical characterization of the adsorbent was carried out by X-Ray Diffraction (XRD), X-Ray Fluorescence (XRF), Energy Dispersive X-Ray attached to Scanning Electron Microscopy (SEM-EDX), BET Specific Surface Area(SSAN2BET) analysis and Fourier-Transform Infrared Spectrometry (FTIR). The effect of various operational parameters such as contact time, initial fluoride concentration, (20-160 mg L-1) adsorbent dose (1-6 g L-1) and initial pH solution (3-11) was evaluated in batch procedures at room temperature (25±2°C). The results of the batch adsorption experiments proved that 24 h of contact time was sufficient for attaining equilibrium. The maximum wastewater defluoridation (84.91%) was obtained for 40 mg L-1 and 3 g L-1 of initial fluoride concentration and adsorbent dose, respectively. It appears that there was no significant effect on the F- removal over a wide range of pH 3-11. Kinetic studies revealed that fluoride adsorption fitted well to pseudo-second-order. The adsorption isotherm of fluoride sorption indicated that the maximum adsorption capacity was noted to be 43.29 mg g-1. Batch adsorption data was better described by Langmuir isotherm confirming monolayer adsorption with homogenous distribution of active sites and without interaction between adsorbed molecules. The obtained results indicated that the ion exchange is probably the main mechanism involved in the F- adsorption by the aluminium-based adsorbent.
Adsorption Characteristics and Charge Transfer Kinetics of Fluoride in Water by Different Adsorbents

Jiaxi Tang,Biao Xiang,Yu Li,Ting Tan,Yongle Zhu

DOI: https://doi.org/10.3389/fchem.2022.917511

IF: 5.5

2022-06-16

Frontiers in Chemistry

Abstract:Water containing high concentrations of fluoride is widely distributed and seriously harmful, largely because long-term exposure to fluoride exceeding the recommended level will lead to fluorosis of teeth and bones. Therefore, it is imperative to develop cost-effective and environmentally friendly adsorbents to remove fluoride from polluted water sources. In this study, diatomite (DA), calcium bentonite (CB), bamboo charcoal (BC), and rice husk biochar (RHB) were tested as adsorbents to adsorb fluoride (F ‐ ) from water, and this process was characterized by scanning electron microscopy (FEI-SEM), X-ray diffraction (XRD), and Fourier-transform infrared spectroscopy (FT-IR). The effects of pH, dosage, and the initial mass concentration of each treatment solution upon adsorption of F ‐ were determined. Kinetic and thermodynamic models were applied to reveal the mechanism of defluoridation, and an orthogonal experiment was designed to obtain the optimal combination of conditions. The results show that the surfaces of CB, BC, and RHB have an irregular pore structure and rough surface, whereas DA has a rich pore structure, clear pores, large specific surface area, and high silica content. With regard to the adsorption process for F ‐ , DA has an adsorption complex electron interaction; that of CB, BC, and RHB occur mainly via ion exchange with positive and negative charges; and CB on F ‐ relies on chemical electron bonding adsorption. The maximum adsorption capacity of DA can reach 32.20 mg/g. When the mass concentration of fluoride is 100 mg/L, the pH value is 6.0 and the dosage is 4.0 g/L; the adsorption rate of F ‐ by DA can reach 91.8%. Therefore, we conclude that DA soil could be used as an efficient, inexpensive, and environmentally friendly adsorbent for fluoride removal, perhaps providing an empirical basis for improving the treatment of fluorine-containing water in the future.

chemistry, multidisciplinary
Efficient removal of fluoride on aluminum modified activated carbon: an adsorption behavioral study and application to remediation of ground water

Anitha Mary Thomas,Kuncham Kuntaiah,Mareswara Rao Korra,S. S. Nandakishore

DOI: https://doi.org/10.1080/10934529.2023.2177059

2023-02-26

Journal of Environmental Science and Health - Part A Toxic/Hazardous Substances and Environmental Engineering

Abstract:In recent times, ground water contamination by toxic elements is of great concern and it is to be addressed for consumption of human, animal, and plant growth. In this context, we have synthesized an adsorbent by modifying commercially available activated carbon with aluminum and tested for de-fluoridation studies. The activity results suggested that the optimized adsorbent is highly efficient in removing the fluoride from ground water. Adsorption maxima are obtained over a wide pH range from 4 to 9, with a contact time of 15 minutes at a dosage of 4 g/L. The results also revealed that the synthesized adsorbent is suitable for application in ground water without any pH adjustment and has exhibited 85%–95% tolerance for common anions in the range of 100–500 mg/L. Equilibrium adsorption isotherm models as well as kinetics of adsorption were applied for the system. An adsorption capacity of 20.4 mg/g and fast kinetics observed are most favorable for defluoridation. Reuse of adsorbent over repeated cycles was investigated. Residual amount of aluminum in treated water is found to be negligible. The removal of toxic elements like Pb, Cd, Cr, Cu, Ni, Zn, As, and Se under the optimized experimental conditions has also been investigated. Al-AC found to be a highly promising material for removal of fluoride and toxic metals from drinking water.
Activated carbon synthesized from biomass material using single-step KOH activation for adsorption of fluoride: Experimental and theoretical investigation

Parimal Chandra Bhomick,Aola Supong,Rituparna Karmaker,Mridushmita Baruah,Chubaakum Pongener,Dipak Sinha

DOI: https://doi.org/10.1007/s11814-019-0234-x

IF: 2.7

2019-04-01

Korean Journal of Chemical Engineering

Abstract:Single-step potassium hydroxide synthesized activated carbon was prepared from Schima wallichii biomass by optimizing process parameters at different carbonization temperature (500 °C, 600 °C, 700 °C and 800 °C) and biomass to KOH impregnation ratio (1: 0, 1: 1, 1: 2 and 1: 3). The optimum condition for obtaining the best activation carbon was found to be at 600 °C and 1: 2 impregnation ratio with BET surface area, total pore volume, and pHzpc of 1,005.71m2g−1, 0.491 cm3g−1 and 6.11, respectively. SEM and XRD analysis revealed the ordering of the graphitic layer with more pores in the carbon matrix at optimized conditions. Batch adsorption experiments were run for fluoride adsorption and fitted, of which Langmuir isotherm model seems to be the best-fitted model with maximum adsorption capacity of 2.524mgg−1. Adsorption kinetics was elucidated best with the pseudo-second-order kinetic model. Theoretical calculations indicate that the adsorption of fluoride is favorable on edge site of both zig-zag and arm chair carbon models with chemisorption type of interaction. Fluoride uptake was found to be affected by the presence of co-ion in the order: CO32−>SO43−>NO3−>Cl−documentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$$ m{CO_3^{2-}} >SO_4^{3-} >NO_3^{-} >Cl^-$$end{document}.

engineering, chemical,chemistry, multidisciplinary
State-of-the-art of research progress on adsorptive removal of fluoride-contaminated water using biochar-based materials: Practical feasibility through reusability and column transport studies

Rakesh Kumar,Prabhakar Sharma,Wen Yang,Mika Sillanpää,Jianying Shang,Prosun Bhattacharya,Meththika Vithanage,Jyoti Prakash Maity

DOI: https://doi.org/10.1016/j.envres.2022.114043

IF: 8.3

2022-11-01

Environmental Research

Abstract:Fluoride (F-) is one of the essential elements found in soil and water released from geogenic sources and several anthropogenic activities. Fluoride causes fluorosis, dental and skeletal growth problems, teeth mottling, and neurological damage due to prolonged consumption, affecting millions worldwide. Adsorption is an extensively implemented technique in water and wastewater treatment for fluoride, with significant potential due to efficiency, cost-effectiveness, ease of operation, and reusability. This review highlights the current state of knowledge for fluoride adsorption using biochar-based materials and the limitations of biochar for fluoride-contaminated groundwater and industrial wastewater treatment. Biochar materials have shown significant adsorption capacities for fluoride under the influence of low pH, biochar dose, initial concentration, temperature, and co-existing ions. Modified biochar possesses various functional groups (-OH, -CC, -C-O, -CONH, -C-OH, X-OH), in which enhanced hydroxyl (-OH) groups onto the surface plays a significant role in fluoride adsorption via electrostatic attraction and ion exchange. Regeneration and reusability of biochar sorbents need to be performed to a greater extent to improve removal efficiency and reusability in field conditions. Furthermore, the present investigation identifies the limitations of biochar materials in treating fluoride-contaminated drinking groundwater and industrial effluents. The fluoride removal using biochar-based materials at an industrial scale for understanding the practical feasibility is yet to be documented. This review work recommend the feasibility of biochar-based materials in column studies for fluoride remediation in the future.

environmental sciences,public, environmental & occupational health
Modeling defluoridation of real-life groundwater by a green adsorbent aluminum/olivine composite: Isotherm, kinetics, thermodynamics and novel framework based on artificial neural network and support vector machine

Saswata Sahu,Manoj Kumar Yadav,Ashok Kumar Gupta,Venkatesh Uddameri,Ashish Navneet Toppo,Bellum Maheedhar,Partha Sarathi Ghosal

DOI: https://doi.org/10.1016/j.jenvman.2021.113965

2022-01-15

Abstract:The kinetic, isotherm, and thermodynamics of adsorptive removal of fluoride from the real-life groundwater was evaluated to assess the applicability of a green adsorbent, aluminum/olivine composite (AOC). The isotherm and kinetics were demonstrated by the Freundlich and Elovich model indicating significant surface heterogeneity of AOC in favouring the fluoride sorption. The fluoride removal efficiency of AOC was achieved as 87.5% after 240 min of contact time. The diffusion kinetic model exhibited that both the intra-particle and film diffusion together control the rate-limiting step of fluoride adsorption. A negative value of ΔG0 (-19.919 kJ/mol) at 303 K confirmed the spontaneous adsorption reaction of fluoride, and its endothermic nature was supported by the negative value of ΔH0 (39.504 kJ/mol). A novel framework for a predictive model by artificial neural network (ANN), and support vector machine (SVM) considering the real and synthetic fluoride-containing water was developed to assess the efficiency of adsorbent under different scenarios. ANN model was observed to be statistically significant (RMSE: 1.0955 and R2: 0.9982) and the proposed method may be instrumental in a similar area for benchmarking the synthetic and real-life samples. The low desorption potential of the spent adsorbent exhibited safe disposal of sludge and the secondary-pollutant-free treated water by the efficient and green adsorbent AOC enhanced the field-scale applicability of the green technology.
Process modeling, characterization, optimization, and mechanisms of fluoride adsorption using magnetic agro-based adsorbent

Mohammad Hadi Dehghani,Solmaz Gholami,Rama Rao Karri,Eder C Lima,Amir Hossein Mahvi,Shahrokh Nazmara,Mehdi Fazlzadeh,Eder C. Lima

DOI: https://doi.org/10.1016/j.jenvman.2021.112173

IF: 8.7

2021-05-01

Journal of Environmental Management

Abstract:In this study, fluoride removal from polluted potable water using magnetic carbon-based adsorbents derived from agricultural biomass was thoroughly investigated. An experimental matrix is designed considering the interactive effects of independent process variables (pH, adsorbent dose, contact time, and initial fluoride concentration) on the removal efficiency. Isotherms and kinetics studies, as well as anions interactions, were also investigated to understand the adsorption mechanisms further. The model parameters of isotherms and kinetics are estimated using nonlinear differential evolution optimization (DEO). Approaches like adaptive neuro-fuzzy inference system (ANFIS) and response surface methodology (RSM) are implemented to predict the fluoride removal and identify the optimal process values. The optimum removal efficiency of GAC-Fe3O4 (89.34%) was found to be higher than that of PAC-Fe3O4 (85.14%). Kinetics experiments indicated that they follow the intraparticle diffusion model, and adsorption isotherms indicated that they follow Langmuir and Freundlich models. Both PAC-Fe3O4 and GAC-Fe3O4 adsorbents have shown an adsorption capacity of 1.20 and 2.74 mg/g, respectively. The model predictions from ANFIS have a strong correlation with experimental results and superior to RSM predictions. The shape of the contours depicts the nonlinearity of the interactive effects and the mechanisms in the adsorption process.

environmental sciences
Application of Chemically Modified Coal Mine Waste for the Sustainable Management of Fluoride in Drinking Water

DOI: https://doi.org/10.3103/s1063455x2403007x

2024-06-07

Journal of Water Chemistry and Technology

Abstract:Waste rocks obtained from mining operations are typically stockpiled due to the lack of their economic value. This practice resulted in significant land occupation and potential for secondary pollution risks due to the lack of probability of leaching. The present study explores the possible utilization of waste rocks as a novel adsorbent for treating F − enriched groundwater. Shale, a coal mine waste was chemically modified by ferrous chloride in a 3 : 1 ratio. Optimization of the adsorption process was done by performing batch adsorption. Surface morphological characterization of the adsorbent was performed by scanning electron microscopy (SEM), energy-dispersive X-ray (EDS), X-ray diffraction (XRD) and Fourier transform infrared spectrophotometer (FTIR). The best results were obtained when 100 mg/L was used to defluoridate contaminated water for 60 min at neutral pH. The efficiency of management was 32% removal at 10 ppm fluoride contamination. Post-treatment adsorbent can be utilized in brick formation to rule out any possibility of secondary/tertiary contamination.

chemistry, physical, applied, analytical
Utilization of organic waste from Chinar leaves as sustainable and eco-friendly adsorbent for fluoride removal

Firdous Ahmad Dar,Swamy Kurella

DOI: https://doi.org/10.1007/s11356-024-35147-z

2024-09-27

Abstract:Due to concerns about high water fluoride concentrations and their detrimental consequences on health, particularly dental and skeletal fluorosis, dependable and cost-effective defluoridation techniques are needed. Chinar leaves (Platanus orientalis), a common waste, might be utilized for the production of activated carbon. For Chinar leaf activated carbon (CLAC) manufacturing, two pre-pyrolysis chemical modification procedures were used: acidic HCl (H-activation) and alkaline NaOH (OH-activation). The success of fluoride removal suggests further research and implementation in locations with fluoride-related water quality issues. This study examines how CLAC dosage, fluoride concentration, temperature, pH, and contact exposure effect defluoridation efficiency. The pseudo-second-order non-linear kinetic model and Freundlich non-linear isotherm model with R2 = 0.99 fit the data, resulting in a peak adsorption capacity of 30.3 mg/g for 0.3 g CLAC. In the present work, the adsorption mechanism was regulated by more than intraparticle diffusion. Adsorption occurred spontaneously as exothermic monolayer chemisorption, according to thermodynamic studies. Adsorbent activated with HCl (H-activated) showed promising results, with 73% F- removal efficiency for OH-activated and 91% for H-activated CLAC.
Synthesis and Characterization of Porous MgO Nanosheet-Modified Activated Carbon Fiber Felt for Fluoride Adsorption

De-Cai Wang,Min-Da Xu,Zhen Jin,Yi-Fan Xiao,Yang Chao,Jie Li,Shao-Hua Chen,Yi Ding

DOI: https://doi.org/10.3390/nano13061082

IF: 5.3

2023-03-16

Nanomaterials

Abstract:In the present work, the porous MgO nanosheet-modified activated carbon fiber felt (MgO@ACFF) was prepared for fluoride removal. The MgO@ACFF was characterized by XRD, SEM, TEM, EDS, TG, and BET. The fluoride adsorption performance of MgO@ACFF also has been investigated. The adsorption rate of the MgO@ACFF toward fluoride is fast; more than 90% of the fluoride ions can be adsorbed within 100 min, and the adsorption kinetics of MgO@ACFF can be fitted in a pseudo-second-order model. The adsorption isotherm of MgO@ACFF fitted well in the Freundlich model. Additionally, the fluoride adsorption capacity of MgO@ACFF is larger than 212.2 mg/g at neutral. In a wide pH range of 2–10, the MgO@ACFF can efficiently remove fluoride from water, which is meaningful for practical usage. The effect of co-existing anions on the fluoride removal efficiency of the MgO@ACFF also has been studied. Furthermore, the fluoride adsorption mechanism of the MgO@ACFF was studied by the FTIR and XPS, and the results reveal a hydroxyl and carbonate co-exchange mechanism. The column test of the MgO@ACFF also has been investigated; 505-bed volumes of 5 mg/L fluoride solution can be treated with effluent under 1.0 mg/L. It is believed that the MgO@ACFF is a potential candidate for a fluoride adsorbent.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology,chemistry
Understanding fluoride adsorption from groundwater by alumina modified with alum using PHREEQC surface complexation model

Francis Adu-Boahene,Patrick Boakye,Frank Ofori Agyemang,Jolly Kanjua,Sampson Oduro‑Kwarteng

DOI: https://doi.org/10.1038/s41598-023-38564-1

IF: 4.6

2023-07-30

Scientific Reports

Abstract:Fluoride is recognized as a vital ion for human and animal growth because of the critical role it plays in preventing skeletal and dental problems. However, when it is ingested at a higher concentration it can cause demineralization of teeth and bones resulting in fluorosis, therefore, the production of high-adsorptive capacity material which is also cost-effective is necessary for the treatment of fluorides. In this study, aluminium foil is valorised into alumina nanoparticles. The as-prepared alumina was modified with alum in two different ratios of 1:0.5 and 1:1 (alumina to alum w/w%) and later used as adsorbents for the removal of fluoride from groundwater. The adsorbents were characterized by Fourier transform infrared spectroscopy, point of zero charge and X-ray diffraction. Different factors that influence the removal efficiency of fluorides such as pH, initial concentrations, contact time and adsorbent dosage were studied and optimized using a simulated fluoride solution. The optimum conditions obtained were used to test real groundwater. The static experiment conditions were used to calibrate a PHREEQC geochemical model which was later used to simulate the fluoride sorption onto the modified alumina at different conditions. PHREEQC was also coupled with parameter estimation software to determine equilibrium constants for the surface reactions between the fluoride species and the adsorbent in a way that the simulations accurately reflect the outcomes of laboratory experiments. Isotherm studies were carried out on the adsorbents. Both Langmuir and Freundlich's non-linear models fitted well for the equilibrium data. However, with a higher coefficient of regression and low chi-square test values, the adsorption process was more of chemisorption on a monolayer surface. Kinetic studies were also carried out by using the non-linear equations from the pseudo-first-order and pseudo-second-order models. The pseudo-second-order model fitted well for the equilibrium data. The mechanism for the fluoride ion adsorption was also studied by the intraparticle (IP) diffusion model and was found that IP was not the rate-determining factor, and therefore the most plausible mechanism for the sorption process was ion exchange or attraction of fluoride ions to the sorbent surface. The findings obtained from this research show that readily available aluminium waste could be valorised into a useful product that could be employed in the removal of fluoride from water samples, including groundwater, that may contain too much fluoride and pose a risk to the general public's health.

multidisciplinary sciences
Portable hydroxyl-functionalized coal gangue-based cordierite porous ceramics sheets for effective adsorption of fluorine-containing wastewater

Deyin Wang,Liming Guo,Zhennan Qiao,Hongwei Liu,Yanlan Zhang,Yongzhen Wang

DOI: https://doi.org/10.1039/d4ra01928h

2024-05-09

Abstract:Monolithic adsorbent removal of fluoride from water is considered an effective and non-secondary pollution method. Here, a portable hydroxyl-functionalized coal gangue-based cordierite porous ceramic sheet (ACGC-Fe) is prepared by using coal gangue solid waste with a specific silicon-aluminum-rich composition ratio and a small amount of magnesium oxide as a raw material through powder compression molding and mild chemical modification. The prepared ACGC-Fe can be used to treat fluorine-containing wastewater and the maximum adsorption of fluorine can reach 18.69 mg g-1. The Langmuir (Freundlich) adsorption isotherm model and pseudo-second-order kinetic model here provided a satisfactory description of the fluoride removal operating mechanism, and it is confirmed that the adsorption mechanism of ACGC-Fe is mainly attributed to the chemisorption of hydrogen bonds (with hydroxyl group) and ionic bonds (with metal), and physical adsorption based on cordierite porous ceramic pores. This research will provide a new idea for designing high-performance materials by mining and analyzing the composition and structure characteristics of coal gangue solid waste itself and broaden the application range of high-value-added coal gangue solid waste.
Mesoporous Carbon from Optimized Date Stone Hydrochar by Catalytic Hydrothermal Carbonization Using Response Surface Methodology: Application to Dyes Adsorption

Faiçal El Ouadrhiri,Majda Elyemni,Amal Lahkimi,Abdelhadi Lhassani,Mehdi Chaouch,Mustapha Taleb

DOI: https://doi.org/10.1155/2021/5555406

2021-04-22

International Journal of Chemical Engineering

Abstract:Providing efficient and environmental friendly ways to recover lignocellulosic waste remains a challenge around the world. In this study, citric acid-catalyzed hydrothermal carbonization (CHTC) was coupled with pyrolysis to convert date seed (Ds) into adsorbent material. In this regard, a central composite design (CCD) using response surface methodology (RSM) was developed to examine the influence of temperature, reaction time, and catalyst dose on the mass yield (Ym(%)) and carbon retention rate (CRR(%)) in the produced hydrochars. The optimized hydrochar (OHC-Ds) was obtained under optimal conditions (200°C, 120 min, 20 mg) and characterized by a Ym(%) and CRR(%) of 59.71% and 75.84%, respectively. Chemical activation by KOH of OHC-Ds followed by pyrolysis at 600°C resulted in an active material (AOHC-Ds) rich in carbon and characterized by a high specific surface area of 1251.5 m2/g, with the dominance of mesopores, as well as an amorphous structure comparable to graphite shown by X-ray diffraction (XRD) analysis. Adsorption experiments of two dyes on AOHC-Ds showed a high maximum adsorption capacity (Qm) of 657.89 mg g−1 for methylene blue (MB) and 384.61 mg g−1 for methyl orange (MO) compared to other conventional adsorbents. This result is due to the low acidity (pHpzc) of the surface of AOHC-Ds, which equals 6.75, and its surface, which is also rich in oxygenated functional groups such as (-OH), (C=O), and (C-O) shown by FTIR analysis. These results suggest that the coupling of CHTC and KOH activation followed by pyrolysis is an encouraging way to prepare an efficient and inexpensive adsorbent to remove dyes in wastewater.

engineering, chemical
Fluoride Removal from Water Sources by Adsorption on MOFs

Athanasia K. Tolkou,Anastasios I. Zouboulis

DOI: https://doi.org/10.3390/separations10090467

2023-08-24

Separations

Abstract:Fluoride is present in several groundwaters due to natural or anthropogenic origins. Although it is necessary for physiological human functions (in small amounts, i.e., 0.5–1.2 mg/L), it could be very harmful when it exceeds the maximum permissible concentration limit of 1.5 mg/L (according to WHO). Among the numerous technologies for removing fluoride from waters, metal–organic framework (MOF) materials are considered to be promising adsorbents due to their advantages of high porosity, high specific surface area, diverse functions and easy modification. In this study, the synthesis of MOFs and the progress of their application to the removal of fluoride from contaminated water, as published in the recent literature mainly over the past five years, are reviewed. The adsorption mechanism(s) and its main characteristics, such as effect of initial fluoride concentration, adsorbent dosage, solution pH, contact time, adsorption capacity, thermodynamic and regeneration studies, etc., for the removal of fluoride with the addition of different MOFs are compared. According to these comparisons, the hydrothermal/solvothermal synthesis method is most commonly used for the preparation of MOFs, whereas higher BET surface areas are shown by specific MOFs based on aluminum metal ions. The main fluoride adsorption mechanisms were found to be electrostatic attraction and/or complexation. The most common pH for conducting experiments was 7.0, but several examined materials were found to be effective over a wide pH range. Four to six regeneration cycles were successfully applied on average, regarding the MOFs under review, whereas in the majority of these cases, the sorption process was found to be endothermic.

chemistry, analytical
Batch fluidized bed reactor based modified biosynthetic crystals: Optimization of adsorptive properties and application in fluoride removal from groundwater

Zhao Wang,Amjad Ali,Junfeng Su,Xiaofen Hu,Ruijie Zhang,Wenshuo Yang,Zizhen Wu

DOI: https://doi.org/10.1016/j.chemosphere.2021.130841

IF: 8.8

2021-10-01

Chemosphere

Abstract:A batch fluidized bed reactor (BFBR) with modified biosynthetic crystals (MBC), derived from Pseudomonas sp. HXF1, was investigated for the treatment of the groundwater containing fluoride (F−). Impacts of different hydraulic retention time (HRT), pH, and initial F− concentration on F− removal were examined and the maximum defluorination efficiency was recorded as 95.20%. Moreover, recycling experiments were performed to evaluate the stability of repeated use. BFBR/MBC system showed a long-term effective treatment outcome with low fluctuation in the concentrations of residual Ca2+ and F−. The formed precipitates were characterized by SEM, XPS, XRD, and FTIR. The defluorination mechanisms of BFBR/MBC system were defined as the chemisorption and induced crystallization of Ca5(PO4)3F on the MBC surface. As a feasible, economical, and environment-friendly technique, the method has a long-term value, which suggests promising applications in F− removal and resourceful treatment.

environmental sciences
Fluoride Removal from Aqueous Solutions by Using Super-Adsorbents of Chitosan/Orange Peels/Activated Carbon@MgO: Synthesis, Characterization, and Adsorption Evaluation

Athanasia K. Tolkou,Apostolos Posantzis,Konstantinos N. Maroulas,Ramonna I. Kosheleva,Ioanna Koumentakou,Margaritis Kostoglou,George Z. Kyzas

DOI: https://doi.org/10.3390/pr12092043

IF: 3.5

2024-09-23

Processes

Abstract:Exposure to excessive concentrations of fluoride in potable water is harmful to human health; therefore, its limitation is deemed necessary. Among the commonly applied technologies, adsorption is selected, as it is a highly effective, simple, and economically efficient treatment. In the present study, several combinations of chitosan (CS), orange peels (OP), activated carbon (AC), and MgO were synthesized and tested as adsorbents in order to find the most effective derivative for fluoride extraction. The impact of the adsorbent dosage, pH level, contact time, and initial concentration was investigated to assess the feasibility of the chitosan/orange peels/activated carbon@MgO composite. According to the results, the modification of chitosan with AC, OP, and MgO in a unique adsorbent (CS/OP/AC@MgO), especially in acidic conditions (pH 3.0 ± 0.1) by using 1.0 g/L of the adsorbent, demonstrated the highest efficiency in F removal, up to 97%. The pseudo-second (PSO) order model and Langmuir isotherm model fit better to the experimental results, especially for CS/OP/AC@MgO, providing a Qm = 26.92 mg/g. Thermodynamic analysis confirmed the spontaneous nature of the adsorption process. The structure and morphology of the modified OP/CS@AC-Mg were extensively characterized using BET, XRD, FTIR, and SEM techniques.

engineering, chemical
Activated Carbon Derived from Peltophorum pterocarpum (Copper Pod) Seeds and Phoenix dactylifera (Date Plam) Seeds in Batch Comparative Adsorption Studies of Fluoride

Keerthi B. Gurani,S.R. Mise,Vinay B. Chakrasali

DOI: https://doi.org/10.53550/eec.2023.v29i01s.032

2023-01-01

Ecology, Environment and Conservation

Abstract:A synthesis of two forms of activated carbons is included in this paper. Because of its capacity to remove contaminants from both air and water, activated carbon (AC) is commonly employed for purification. Its porous structure allows it to trap impurities, and it is frequently suggested for a variety of water and wastewater treatment applications. However, due to the high expense of filing an AC application, the number of applications that can be filed is limited. AC was made using locally accessible Peltophorum pterocarpum (Copper Pod) and Phoenix dactylifera (Date Plam) seeds in this study. Fluoride adsorption on physical activated carbon from a synthetic sample made from Peltophorum pterocarpum (Copper Pod) and Phoenix dactylife. To remove fluorine from the body physically activated carbon, adsorption in batches methods were completed in order to find the best time, dose, pH sorption kinetics, and sorption equilibrium. The ideal contact duration, dosage of adsorbent and carbon pH were found to be 30 minutes, 140 mg, and 8.00, and 50 minutes, 225 mg, and 9.00, with fluoride removal efficiency of 77.5 percent, 79.33 percent, 82.6 percent, and 72.63 percent, 75.8%, 76.5 percent, respectively. Changes in process factors such as adsorption time and dosage were recycled to inspect adsorption kinetics and sorption isotherm models. The isotherms of Langmuir, Freundlich, and Temkin are three scientists investigated using This experimental data has been determined to be accurate.
Fibrous adsorbents derived from polyphenolic chemistry for remediation of fluoride contamination at low concentrations

Meng Zhang,Meng Xiao,Wenqian Qi,Hui Mao

DOI: https://doi.org/10.1016/j.seppur.2023.125665

IF: 8.6

2023-11-22

Separation and Purification Technology

Abstract:Fluoride contamination in drinking water is one of the most concerned environmental issues. Herein, a new type of fibrous adsorbent was prepared by polyphenolic chemistry enabled facile synthesis approach that was dependent on the surface modification of chitosan fibers (CF) with plant polyphenols, followed by the chelation with Zr(IV) (CF-Zr). The presence of plant polyphenols allow for a facile and stable anchoring of Zr(IV) onto the CF, which provided sufficient active sites for the adsorption of fluoride at low concentrations. Notably, at low concentration of 2.0 mg/L, the CF-Zr was capable of removing 97.59 % of fluoride, which was considerably higher than commercial activated carbon (3.58 %). The outstanding adsorption performances of CF-Zr to fluoride was attributed to the Zr(IV), which provided high affinity to fluoride by the formation of Zr-oxyfluoride species. The fibrous morphology of the CF-Zr guaranteed a fast adsorption process, with ∼ 30 min to reach the adsorption equilibrium. The Langmuir model well fitted the adsorption isotherms, and the corresponding equilibrium adsorption capacity was determined to be 74.52 mg g −1 , close to the experimentally determined maximum adsorption capacity (77.04 mg g −1 ). The fluoride adsorbed onto the CF-Zr was desorbed by NaOH solution, with the desorption percentage of 90.22 %.

engineering, chemical
Fluoride removal in water by a hybrid adsorbent lanthanum-carbon

Esmeralda Vences-Alvarez,Litza Halla Velazquez-Jimenez,Luis Felipe Chazaro-Ruiz,Paola E Diaz-Flores,Jose Rene Rangel-Mendez

DOI: https://doi.org/10.1016/j.jcis.2015.05.048

2015-10-01

Abstract:Various health problems associated with drinking water containing high fluoride levels, have motivated researchers to develop more efficient adsorbents to remove fluoride from water for beneficial concentrations to human health. The objective of this research was to anchor lanthanum oxyhydroxides on a commercial granular activated carbon (GAC) to remove fluoride from water considering the effect of the solution pH, and the presence of co-existing anions and organic matter. The activated carbon was modified with lanthanum oxyhydroxides by impregnation. SEM and XRD were performed in order to determine the crystal structure and morphology of the La(III) particles anchored on the GAC surface. FT-IR and pK(a)'s distribution were determined in order to elucidate both the possible mechanism of the lanthanum anchorage on the activated carbon surface and the fluoride adsorption mechanism on the modified material. The results showed that lanthanum ions prefer binding to carboxyl and phenolic groups on the activated carbon surface. Potentiometric titrations revealed that the modified carbon (GAC-La) possesses positive charge at a pH lower than 9. The adsorption capacity of the modified GAC increased five times in contrast to an unmodified GAC adsorption capacity at an initial F(-) concentration of 20 mg L(-1). Moreover, the presence of co-existing anions had no effect on the fluoride adsorption capacity at concentrations below 30 mg L(-1), that indicated high F(-) affinity by the modified adsorbent material (GAG-La).

Functional activated carbon: from synthesis to groundwater fluoride removal

Nano-magnetically modified activated carbon prepared by oak shell for treatment of wastewater containing fluoride ion

Synthesis and characterization of aluminum-based adsorbent and application in fluoride removal from aqueous solution

Adsorption Characteristics and Charge Transfer Kinetics of Fluoride in Water by Different Adsorbents

Efficient removal of fluoride on aluminum modified activated carbon: an adsorption behavioral study and application to remediation of ground water

Activated carbon synthesized from biomass material using single-step KOH activation for adsorption of fluoride: Experimental and theoretical investigation

State-of-the-art of research progress on adsorptive removal of fluoride-contaminated water using biochar-based materials: Practical feasibility through reusability and column transport studies

Modeling defluoridation of real-life groundwater by a green adsorbent aluminum/olivine composite: Isotherm, kinetics, thermodynamics and novel framework based on artificial neural network and support vector machine

Process modeling, characterization, optimization, and mechanisms of fluoride adsorption using magnetic agro-based adsorbent

Application of Chemically Modified Coal Mine Waste for the Sustainable Management of Fluoride in Drinking Water

Utilization of organic waste from Chinar leaves as sustainable and eco-friendly adsorbent for fluoride removal

Synthesis and Characterization of Porous MgO Nanosheet-Modified Activated Carbon Fiber Felt for Fluoride Adsorption

Understanding fluoride adsorption from groundwater by alumina modified with alum using PHREEQC surface complexation model

Portable hydroxyl-functionalized coal gangue-based cordierite porous ceramics sheets for effective adsorption of fluorine-containing wastewater

Mesoporous Carbon from Optimized Date Stone Hydrochar by Catalytic Hydrothermal Carbonization Using Response Surface Methodology: Application to Dyes Adsorption

Fluoride Removal from Water Sources by Adsorption on MOFs

Batch fluidized bed reactor based modified biosynthetic crystals: Optimization of adsorptive properties and application in fluoride removal from groundwater

Fluoride Removal from Aqueous Solutions by Using Super-Adsorbents of Chitosan/Orange Peels/Activated Carbon@MgO: Synthesis, Characterization, and Adsorption Evaluation

Activated Carbon Derived from Peltophorum pterocarpum (Copper Pod) Seeds and Phoenix dactylifera (Date Plam) Seeds in Batch Comparative Adsorption Studies of Fluoride

Fibrous adsorbents derived from polyphenolic chemistry for remediation of fluoride contamination at low concentrations

Fluoride removal in water by a hybrid adsorbent lanthanum-carbon