Abstract:In order to explore whether (Nb,W) co-alloying TiAl-based alloys with relatively higher W addition have better high-temperature tensile rupture property, Ti-44Al-4Nb-1 W-0.1B alloy is designed and prepared. Ti-44Al-8Nb-0.1B alloy and Ti-44Al-7.2Nb-0.2 W-0.1B alloy are also prepared for comparative study. The rupture property testing is carried out at 800 °C and different tensile stresses. The property data , macro/microstructure evolution, fracture surface, W content, crack failure behaviors are studied. The results show that the (Nb,W) co-alloying alloys have better rupture property than the pure Nb alloying alloy. For the (Nb,W) co-alloying alloys, the higher W contained Ti-44Al-4Nb-1 W-0.1B alloy has the better property under lower tensile stress, and the lower W contained Ti-44Al-7.2Nb-0.2 W-0.1B alloy has the better property under higher tensile stress. The relationships of rupture life t and stress σ for the three alloys are given. All the three alloys have a coupling fracture mode of ductile fracture and brittle fracture. The ductile fracture exhibits the typical dimple characteristics. The brittle fracture exhibits the typical trans-granular cleavage, river-like pattern and trans-lamella fracture characteristics. The higher the stress, the more brittle fracture characteristics there are. After rupture property testing, the (α 2 + γ) lamella colony sizes of the three alloys all decrease, indicating that DRX and grain boundary slip occur not only along (α 2 + γ) lamella colony boundary, but also inside it. The colony boundary regions have the stress concentration, where the B2 phase produces the better buffering and coordination, and as well as the dislocation tangles, DRX and grain boundary slip can be found by EBSD and TEM. EPMA results show that the more W added in the alloy, the more W content is in the (α 2 + γ) lamella matrix, which is beneficial for the rupture property. However, more W addition will also lead to the formation of more B2 phase in the initial as-cast microstructure. So that, under higher tensile stress, when the stress intensity factor K is higher, the crack failure is more likely to occur.

Effect of Re and W upon brittle fracture in Ni3Al cracks by atomic simulation

Effect of Re on lattice trapping in γ′-Ni3Al cracks by atomistic simulation

Effects of Re, W and Co on dislocation nucleation at the crack tip in the γ-phase of Ni-based single-crystal superalloys by atomistic simulation

Influence of Re on the Propagation of A Ni/Ni-3 Al Interface Crack by Molecular Dynamics Simulation

Influence of the alloying elements Re, Co and W on the propagation of the Ni/Ni3Al interface crack

Molecular dynamics simulations of influence of Re on lattice trapping and fracture stress of cracks in Ni

Effect Of Re On Lattice Trapping In Gamma '-Ni3al Cracks By Atomistic Simulation

The Effects of Refractory Elements on Mechanical Properties in CoCrNiFe Concentrated Solid Solution Alloys Across Different Temperatures

First-principles Study of Ni/Ni3Al Interface Doped with Re, Ta and W

The Effect of Ta, W, and Re Additions on the Tensile-Deformation Behavior of Model Ni-based Single-Crystal Superalloys at Intermediate Temperature

Strengthening effect of rhenium on different substitution positions of tungsten nanofilm at high temperature: DFT and molecular dynamics simulation

Effect of Re on mechanical properties of single crystal Ni-based superalloys: Insights from first-principle and molecular dynamics

Effect of Re on dislocation nucleation from crack tip in Ni by atomistic simulation

Impact of replacement of Re by W on dislocation slip mediated creeps of γ′-Ni3Al phases

Effects of alloying elements on the super-lattice intrinsic stacking fault energy and ideal shear strength of Ni 3 Al crystals

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

Theoretical Calculations of the Ideal Strength of Ni, NiAl and Ni3Al in Tension and Shear

The influence of transition metal solutes on dislocation core structure and values of Peierls stress and barrier in tungsten

Research on the Effect Mechanism of Re on Interface Dislocation Networks of Ni–Based Single Crystal Alloys

High-temperature tensile rupture property of (Nb,W) co-alloying TiAl-based alloys

Effect of alloying element on dislocation cross-slip in gamma '-Ni3Al: a first-principles study