Abstract:L-Leucine (LL) has been widely used to enhance the dispersion performance of powders for inhalation. LL can also protect powders against moisture, but this effect is much less studied. The aim of this study was to investigate whether LL could prevent moisture-induced deterioration in in vitro aerosolization performances of highly hygroscopic spray-dried powders. Disodium cromoglycate (DSCG) was chosen as a model drug and different amounts of LL (2-40% w/w) were added to the formulation, with the aim to explore the relationship between powder dispersion, moisture protection and physicochemical properties of the powders. The powder formulations were prepared by spray drying of aqueous solutions containing known concentrations of DSCG and LL. The particle sizes were measured by laser diffraction. The physicochemical properties of fine particles were characterized by X-ray powder diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and dynamic vapor sorption (DVS). The surface morphology and chemistry of fine particles were analyzed by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and time-of-flight secondary ion mass spectrometry (ToF-SIMS). In vitro aerosolization performances were evaluated by a next generation impactor (NGI) after the powders were stored at 60% or 75% relative humidity (RH), and 25°C for 24h. Spray-dried (SD) DSCG powders were amorphous and absorbed 30-45% (w/w) water at 70-80% RH, resulting in deterioration in the aerosolization performance of the powders. LL did not decrease the water uptake of DSCG powders, but it could significantly reduce the effect of moisture on aerosolization performances. This is due to enrichment of crystalline LL on the surface of the composite particles. The effect was directly related to the percentage of LL coverage on the surface of particles. Formulations having 61-73% (molar percent) of LL on the particle surface (which correspond to 10-20% (w/w) of LL in the bulk powders) could minimize moisture-induced deterioration in the aerosol performance. In conclusion, particle surface coverage of LL can offer short-term protection against moisture on dispersion of hygroscopic powders.

Optimization of Spray-Drying Process Parameters to Study Anti-Sticking Effect of Hydroxypropyl Methyl Cellulose-VLV on Corni fructus Extracts

Preparation of Sustained Release Capsules by Electrostatic Dry Powder Coating, Using Traditional Dip Coating As Reference

Low-viscosity hydroxypropyl methylcellulose obtained by electron beam irradiation and its performance in spray drying

Optimization of Microcrystalline Cellulose PH 101, Lactose, and Kollidon® K 30 To Obtain Co-Processed Excipient Through Spray Drying

Optimization of Drying Conditions and Components to Reduce Wall Sticking During Spray Drying of Infant Formula Milk

The preparation, characterization, and application of porous core–shell composite particles produced with laboratory-scale spray dryer

Spray dried powder of common fruit juices: Enhancement of main properties

Preparation of Hydroxypropyl Methylcellulose Acetate Succinate with a Narrow Molecular Weight Dispersion

Surface Enrichment and Depletion of the Active Ingredient in Spray Dried Amorphous Solid Dispersions

Tuning The Morphology Of Microparticles From Spray Drying Of Cellulose Nanocrystal Suspensions By Hydrophobic Lignin

Facile superhydrophobic modification on HPMC film using polydimethylsiloxane and starch granule coatings

Concordance of vacuum compression molding with spray drying in screening of amorphous solid dispersions of itraconazole

Modification on Drying Chamber Wall of Spray Dryer Towards Better Yield

Optimization of Spray-Drying Workflow As A Method for Preparing Concentrated Cultures of Lactobacillus Fermentum

Optimized Design of Material Preparation for Cotton Linters-Based Carbon Black Dispersion Stabilizers Based on Response Surface Methodology

L-Leucine as an excipient against moisture on in vitro aerosolization performances of highly hygroscopic spray-dried powders

Dry Bacterial Cellulose and Carboxymethyl Cellulose formulations with interfacial-active performance: processing conditions and redispersion

Konjac glucomannan hydrolysate: A potential natural coating material for bioactive compounds in spray drying encapsulation

Facile Synthesis of Highly Hydrophobic Cellulose Nanoparticles Through Post-Esterification Microfluidization

Studies on new co-processed excipient consisting of lactose and gelatinized starch

Application of edible coating pretreatment before drying to prevent loss of plant essential oil: A case study of Zanthoxylum schinifolium fruits