Abstract:Recently, various miniaturized electronic systems and the rapid increase in power density of microelectronic devices have created additional requirements for micro-scale heat dissipation technology. To dissipate heat in a micro-scale region efficiently, several creative cooling methods for high heat flux dissipation have been designed on the order of 1000 W/cm(2). Due to its high surface-to-volume ratio, the microchannel heat sink has become the most popular one among emerging technologies and an effective tool for high heat flux thermal management. Nevertheless, in common electronic microchannel cooling systems, the traditional parallel microchannel causes a dramatic pressure loss along channel length. In this regard, the manifold microchannel heat sink cooling technology becomes promising with its high heat dissipation potential and moderate pressure drop penalty. The shortened effective flow length compared with the traditional microchannel provides a smaller pressure drop and delays the onset of the critical-heat-flux point. However, while a number of numerical and experimental studies have been conducted for the single-phase flow in the manifold microchannel, two-phase flow boiling in this kind of channel is not widely employed because of its issues with flow pattern prediction. This work develops a new solver based on open source software OpenFOAM to perform the transient process of subcooled flow boiling in the manifold microchannel heat sink. Additionally, heat transfer in the silicon substrate is considered to improve the accuracy of simulation. Similar to single-phase flow simulation for the manifold microchannel, a unit cell model extracted from the whole cooling plate is employed for the two-phase boiling flow to avoid huge computational costs. Through several reasonable assumptions, the symmetry boundary condition is applied on four lateral surfaces in the unit cell, while uniform heat flux is adopted on the bottom wall. A uniform inlet velocity boundary estimated from the total volume flow rate condition is coupled with a fixed temperature value of 7 degrees C lower than saturation temperature. After the mesh independence test, the self-programming solver and numerical methods are validated by comparing numerical results with experimental data. It is determined that the boiling curve obtained by the empirical rate phase-change model with parameters r(1)=r(v)=100 agrees well with experimental results. Furthermore, heat transfer and pressure drop performance differences are caused by microchannel width w(c) and fin width w(f). In comparison to sample A (w(c)=w(f)=15 mu m), decreasing wc and wf simultaneously leads to lower average wall temperature of the heated surface; the channel pressure drop between inlet and outlet surfaces rises dramatically when the widths decrease. When the total number of microchannels in the manifold microchannel cooling plate remains unchanged, increasing wc results in a decreased wf. Based on experimental results, heat sink sample C shows that the pressure loss can be considerably reduced under the premise of sacrificing a small degree of heat transfer performance, which can be attributed to the increased microchannel hydraulic diameter. The manifold microchannel heat sink with w(c)>w(f) is recommended for practical application due to lower pressure loss and average temperature variation.

CFD-simulation of non-stationary heat transfer of water and nanofluid in saturated state

CFD Simulations and Experimental Verification on Nucleate Pool Boiling of Liquid Nitrogen

Investigation of Bubble Interaction in a Temporal and Spatial Heat Flux Partitioning Model for Subcooled Flow Boiling

Heat Transfer Characteristics and Chf Prediction in Nanofluid Boiling

Cfd -Based Modelling On Inter Facial Heat Transfer For Water Quenching

A Phase Field Method for Numerical Simulation of Boiling Heat Transfer

An investigation on the heat transfer characteristics of nanofluids in flow boiling by molecular dynamics simulations

Numerical Investigation Of Flow Boiling In A Manifold Microchannel Heat Sink With Conjugate Heat Transfer

A study of convective heat transfer by using the hybrid MD-FVM method

Interface Capturing Flow Boiling Simulations in a Compact Heat Exchanger

Development of a new semi-mechanistic wall boiling heat transfer model for CFD methodology focusing on macroscopic parameters

Numerical Simulation of Heat Transfer During Boiling Flow of Cryogenic Fluid in Vertical Tube

Numerical Simulation Of Heat And Mass Transfer In Air-Water Direct Contact Using Computational Fluid Dynamics

Numerical Simulation of Subcooled Flow Boiling in a Manifold Microchannel Heat Sink

Computational Modelling and Simulations to Study the Thermal Enhancement in Nanofluid Flow in Undulating Wavy Cavity of a Cylinder: Finite Element Analysis

CFD-Based Numerical Simulation of Water Film Flash Evaporation with a New Flash Evaporation Model

Implementation and validation of two-phase boiling flow models in OpenFOAM

About the 3D simulation of the boiling of liquid films and spray droplets during their contact with hot substrates

Molecular Dynamics Study of Phase Transition Heat Transfer in Water Nanofilm on Nanorough Surfaces

A Molecular Dynamics Simulation on the Convective Heat Transfer in Nanochannels

Numerical simulation of boiling behavior in vertical microchannels