Abstract:This study analyzes the combustion of pellets and briquettes made of plant biomass in low-power heating devices powered periodically with fuel being placed on the grate, as well as after modification using an automatic fuel feeding system in the gutter burner. The use of herbaceous biomass in the form of pellets in low-power heating devices with automatic fuel feeding and combustion in a gutter burner is not widely promoted and popular. Therefore, this study used four types of herbaceous waste biomass (wheat straw, rye straw, oat straw and hay) and one type of woody waste biomass (birch sawdust) for testing. The basic chemical characteristics were determined for the raw materials. After appropriate preparation, the selected starting materials were subjected to briquetting and pelleting processes. Selected physical properties were also determined for the obtained biofuels. Biofuels made from birch sawdust had the lowest heat value (16.34 MJ·kg−1), although biofuels made from wheat, rye and hay straw had a slightly lower calorific value, respectively: 16.29; 16.28 and 16.26 MJ·kg−1. However, the calorific value of oat straw biofuels was only 15.47 MJ kg−1. Moreover, the ash content for herbaceous biomass was 2–4 times higher than for woody biomass. Similar differences between herbaceous and woody biomass were also observed for the nitrogen and sulfur content. To burn the prepared biofuels, a domestic grate-fired biomass boiler was used, periodically fed with portions of fuel in the form of pellets or briquettes (type A tests), which was then modified with a gutter burner enabling the automatic feeding of fuel in the form of pellets (type B tests). During the combustion tests with simultaneous timing, the concentration of CO2, CO, NO and SO2 in the exhaust gases was examined and the temperature of the supplied air and exhaust gases was measured. The stack loss (qA), combustion efficiency index (CEI) and toxicity index (TI) were also calculated. The research shows that the use of automatic fuel feeding stabilizes the combustion process. The combustion process is balanced between herbaceous and woody biomass biofuels. Disparities in CO2, CO and Tgas emissions are decreasing. However, during type B tests, an increase in NO emissions is observed. At the same time, the research conducted indicates that the combustion of herbaceous biomass pellets with their automatic feeding into the combustion chamber is characterized by an increase in combustion efficiency, indicating that when the combustion process is automated, they are a good replacement for wood biofuels—both pellets and briquettes.

Assessment of Quality Indicators of Pressed Biofuel Produced from Coarse Herbaceous Plants and Determination of the Influence of Moisture on the Properties of Pellets

Characterizing value-added pellets obtained from blends of miscanthus, corn stover, and switchgrass

Energy Evaluation and Greenhouse Gas Emissions of Reed Plant Pelletizing and Utilization as Solid Biofuel

Prediction of Storage Conditions to Increase the Bioenergy Efficiency of Giant Miscanthus Pellets Produced through On-Site Integrated Pretreatment Machines

Combustion Efficiency of Various Forms of Solid Biofuels in Terms of Changes in the Method of Fuel Feeding into the Combustion Chamber

Evaluation of Agricultural Residues as Organic Green Energy Source Based on Seabuckthorn, Blackberry, and Straw Blends

Evaluation of the Productivity and Potential Utilization of Artemisia dubia Plant Biomass for Energy Conversion

Experiment research on utilization of particle biomass fuel in sintering process

Exploring the Potential of Perennial Nectar‐Producing Wild Plants for Pellet Combustion

The Quality of Virginia Fanpetals Biomass as an Energy Source, Depending on the Type of Propagating Material and Plantation Age

Short rotation woody crops and forest biomass sawdust mixture pellet quality

Modeling and optimization of compaction pressure, binder percentage and retention time in the production process of carbonized sawdust-based biofuel briquettes using response surface methodology (RSM)

The pelletization and torrefaction of coffee grounds, garden chaff and rapeseed straw

Assessment of plant biomass for pellet production using multivariate statistics (PCA and HCA)

Determination of Strength Properties of Energy Plants on the Example of Miscanthus × Giganteus, Rosa Multiflora and Salix Viminalis

Mechanical Aspects and Applications of Pellets Prepared from Biomass Resources

Impact of cultivation conditions on physicochemical characteristics of Miscanthus × giganteus biomass

Pelletization property analysis of raw and torrefied corn stalks for industrial application to achieve agricultural waste conversion

Qualitative analysis of pellets produced from Jerusalem artichoke (Helianthus tuberosus L.)

Comparative investigation on fuel characteristics of different parts of corn stover considering particle size and pelletizing pressure based on macro-TGA

Development of an efficient method to blend forest biomass with agricultural residue to produce fuel pellets with improved mechanical properties