Abstract:The present study numerically examines heat transfer and flow in circular tubes fitted with dimpled twisted tape inserts, and Al2O3-water nanofluid is employed. Considering the effects of dimples, protrusions, nanofluid volume fraction a and nanoparticle" diameter tip, the discussion and analysis on heat transfer, flow characteristics, turbulence kinetic energy TICE, thermal property, entropy generation and maximum local wall temperature T-max are detailedly provided. The results show that dimple side and protrusion side both realize great heat transfer enhancement, and dimple side behaves better compared with protrusion side. Utilization of dimples leads to an increase by 25.53% in convective heat transfer coefficient It at most compared with smooth tape. Heat transfer performance is greatly improved on both tape wall and tube wall owing to disturbance to flow structures. The overall TILE level significantly rises especially close to the core flow region when dimples are adopted, and overall swirl flow intensity greatly increase, further resulting in enhancement of turbulent mixing and heat transfer. Remarkable decline in average heat transfer entropy generation rate S-ah is identified, accompanied by slight rise in average friction entropy generation rate S-af, where average total entropy generation rate S-a inclines by 29.10% at most in comparison with smooth tape. Besides, the employment of nanofluids results in great improvement of heat transfer, with further enhanced effect when alpha increases, accompanied by slight growth in resistance. A maximum increase by 58.96% in h is identified compared with basefluid case, and it is quite helpful that in this case the maximum rise in friction factor is only 5.05%. The wall temperature distribution is greatly improved using nanofluid, and nanofluid case provides markedly improved thermal conductivity distribution in spite of slight growth in dynamic viscosity. The heat transfer in recirculation-caused low heat transfer regions is further promoted through nanofluids when dimple technique is adopted. Utilization of nanofluid brings about a significant reduction in S-ah, the effect of which is further promoted by a rising cc, with a slight increase in S-af where S-a is reduced by 28.89% at most. The T-max greatly declines using nanofluids with further enhanced effect when alpha ascends. Furthermore, utilization of smaller d(p) gives rise to significant heat transfer enhancement compared with the larger one, with extremely mild resistance increase. Lower S-a and lower T-max are both realized when smaller d(p) is used, and the effect of d(p) reaches an extremely low level when it exceeds 40 nm. (C) 2017 Elsevier Ltd. All rights reserved.

Performance Analysis of Solar Water Heater Using Al2O3 NanoParticle with Plain-Dimple Tube Design

Performance analysis of parabolic type solar water heater by using copper-dimpled tube with aluminum coating

Experimental and Computational Analysis of Aluminum-Coated Dimple and Plain Tubes in Solar Water Heater System

Experimental analysis of the effect of copper dimple tube with aluminum coating on the performance of parabolic solar water heater using helically twisted tape

Performance enhancement by tungsten trioxide and silicon dioxide mixed nanofluids in solar collector of evacuated tube type

Numerical simulation of the performance of a novel parabolic solar receiver filled with nanofluid

Numerical analysis with experimental validation for thermal performance of flat plate solar water heater using CuO/distilled water nanofluid in closed loop

Heat Transfer Characteristics of Plate Heat Exchanger with Bubble Fin Using Al2O3/Water Nanofluid: Numerical Investigation

Numerical investigation on the effect of Al 2 O 3 -water nanofluid on direct steam generation in parabolic trough collectors

Comparative performance assessment of different absorber tube geometries for parabolic trough solar collector using nanofluid

Property of Water-Nanoparticle Flow and Heat Transfer in the Double-Tube Heat Exchanger with Nanofluid

An experimental investigation on the effect of Al2O3/distilled water nanofluid on the energy efficiency of evacuated tube solar collector

Investigation on influence of dimpled surfaces on heat transfer enhancement and friction factor in solar water heater

Performance analysis of a plate heat exchanger using various nanofluids

Performance enhancement and comparison of inner-shielded solar parabolic trough collector with various nanoparticles in Syltherm-800 using computational fluid dynamics techniques

Numerical Investigation on Heat Transfer Performance and Flow Characteristics in Circular Tubes with Dimpled Twisted Tapes Using Al 2 O 3 -Water Nanofluid

Thermal performance simulation of parabolic trough collector with ternary nanofluid flows and half-star-shaped fins inserts in different receivers

Experimental Investigation of Convective Heat Transfer Performance of TiN Nanofluid Charged U-Pipe Evacuated Tube Solar Thermal Collector

Heat transfer characteristics of plate heat exchanger using hybrid nanofluids: effect of nanoparticle mixture ratio

Thermal and Thermodynamic Comparison of Smooth and Convergent‐divergent Parabolic Trough Absorber Tubes with the Application of Mono and Hybrid Nanofluids

Thermal Characterization of Flat Plate Solar Collector Using Titanium Dioxide Nanofluid